McIntosh MX121, Руководство пользователя

Страница: 13 / 52

13
MX121 Zone 2 Input and Output Connections
MX121 Zone 2 Input Connections
MX121 Zone 2 Output Connections
In a typical MX121 two Zone Audio/Video System,
Source Components can share the same Data Port
Connections. The two Zones of the MX121 also share
the same Analog Audio and Component Video Con-
nections. The additional Analog Audio and Video
Connections below are for Source Components con-
nected to Main Zone via Digital Connections, as Zone
2 is Analog Audio/Video only.
The MX121 Zone 2 Input Connection Diagram (lo-
cated on the separate folded sheet “ Mc3A and Mc3B ”)
is an example of a typical Zone 2 Second Room
System. Your system may vary from this, however the
actual components would be connected in a similar
manner. For additional information refer to “Connec-
tor and Cable Information” on page 6.
Note: The following connections made to the MX121
are using the default settings. To make changes to
the default settings proceed to Setup Mode start-
ing on page 16.
Sensor Connections:
1. Connect the Zone 2 Sensor to a external IR Con-
nection Block and the output of the Connection
Block to the MX121 IR IN Jack.
Note: If there is no external Sensor used for the
Main Zone, a splitter is not needed. Connect
the Zone 2 Sensor directly to the MX121 IR IN
Jack.
Analog Audio Connections:
2. Connect an Audio Cable from the MX121 ANA-
LOG INPUT IN TUNER Jacks to the AM/FM
Tuner unbalanced Output Jacks.
3. Connect an Audio Cable from the MX121 ANA-
LOG INPUT IN BD Jacks to the Audio/Video
Disc Player Audio Outputs Unbalanced 2CH Jacks.
4. Connect an Audio Cable from the MX121 ANA-
LOG INPUT IN SAT Jacks to the Satellite Analog
Output Jacks.
Analog Video Connections:
5. Connect Component Video Cables from the
MX121 COMPONENT VIDEO IN 1 Jacks to the
Audio/Video Disc Player Component Video Out-
put Jacks, making sure to match the “Y”, “PB” and
“PR” connections at both ends.
6. Connect Component Video Cables from the
MX121 COMPONENT VIDEO IN 3 Jacks to the
Satellite Component Video Output Jacks, making
sure to match the “Y”, “PB” and “PR” connections
at both ends.
The MX121 has the ability to automatically switch
power On/Off to McIntosh Power Amplifiers via the
Power Control/Trigger connections.
The following connection instructions, together
with the MX121 Zone 2 Output Connection Diagram
located on the separate folded sheet “ Mc3B ”, is an
example of a typical Zone 2 Second Room System.
Your system may vary from this, however the actual
components would be connected in a similar manner.
For additional information refer to “Connector and
Cable Information” on page 6.
Note: The following component connections made to
the MX121 are using the default settings.
Power Control Connections:
1. Connect a Control Cable from the MX121 PWR
CTRL/TRIGGER (Power Control) 2 Jack to the
Power Control In on Zone 2 Power Amplifier.
2. Connect any additional McIntosh Components in a
similar manner, as outlined in step 1.
Analog Audio Connections:
3. Connect Audio Cables from the MX121 ANA-
LOG AUDIO OUT Zone 2 OUT Jacks - L (Left
Channel) and R (Right Channel) to Zone 2 Power
Amplifier Left and Right respectively.
Analog Video Connections:
4. Connect Component Video Cables from the
MX121 COMPONENT VIDEO OUT 2/ZONE 2
Jacks to the Zone 2 TV/Monitor Video Input Jacks,
making sure to match the “Y”, “PB” and “PR”
connections at both ends.
AC Power Cords Connections:
5. Connect the MX121 and any remaining compo-
nents’ AC Power Cords to a live AC outlet.