Maurer DN1100, Перевод из оригинального руководства, Страница: 5 / 43

G e n e r a l I n f o r m a t i o n
Power Module DN Version 09.2019 Page 5/43
6.5.4 PIN4 Fault .......................................................................................................................................... 21
6.5.5 PIN5 Active ........................................................................................................................................ 21
6.5.6 PIN7 Process OK (Process Monitoring Step 1, Optional) .................................................................. 22
6.5.7 PIN10 External enable signal ............................................................................................................. 22
6.5.8 PIN11 Module Ready ......................................................................................................................... 22
6.5.9 PIN14/15 Analogue out (Field strength proportional signal)............................................................... 22
6.5.10 Interface board D-Sub15 .................................................................................................................... 23
6.5.11
Status LED P1… P12 description ...................................................................................................... 23
6.5.12 Interface module fieldbus coupler ...................................................................................................... 24
6.6
Power setting (MM DN750…1850, optional) ......................................................................................... 26
6.6.1 Power setting via selector switch ....................................................................................................... 26
6.6.2 D-SUB9 power setting interface ......................................................................................................... 26
6.6.3 Configuration D-Sub9 connector ........................................................................................................ 26
6.7 Continuous demagnetization ................................................................................................................. 26
6.8 Safety control ......................................................................................................................................... 27
6.8.1 Safe Torque Off (STO), Optional ....................................................................................................... 27
7 Demagnetization ..................................................................................................................... 28
8 Maintenance ............................................................................................................................ 29
8.1 Daily maintenance interval ..................................................................................................................... 29
8.1.1 Visual check ....................................................................................................................................... 29
8.2 Monthly maintenance interval ................................................................................................................ 29
8.2.1 Visual check ....................................................................................................................................... 29
8.2.2 Functional check ................................................................................................................................ 29
8.2.3 Maintenance ...................................................................................................................................... 29
8.3 Yearly maintenance interval .................................................................................................................. 29
8.3.1 Functional check ................................................................................................................................ 29
8.4 Spare and wear parts ............................................................................................................................ 30
8.4.1 Fuse protection .................................................................................................................................. 30
8.4.2 Inverter replacement .......................................................................................................................... 30
8.5 Decommissioning .................................................................................................................................. 31
8.5.1 Disassemble ...................................................................................................................................... 31
8.5.2 Disposal ............................................................................................................................................. 31
9 Troubleshooting ..................................................................................................................... 32
9.1 Ready lamp dark / no Ready signal: ...................................................................................................... 32
9.2 Active lamp flashing / Active Signal flashing (5 Hz) ............................................................................... 32
9.3 Fault lamp flashing / Fault Signal flashing (5 Hz) ................................................................................... 32
9.4 Fault lamp indicates / +24VDC on Fault signal: ..................................................................................... 32
9.5 Process OK lamp dark / no Process OK signal: .................................................................................... 32
9.6 False triggering of the RCCB, ELCB...................................................................................................... 33
9.7 Insufficient demagnetization .................................................................................................................. 33
9.8 Demagnetization pulse check ................................................................................................................ 34
9.9 Malfunction external coil fan at Fan connector ...................................................................................... 34
9.10 Error analysis LED interface board ........................................................................................................ 35
10 Specifications ......................................................................................................................... 36
10.1 General .................................................................................................................................................. 36
10.1.1 Minimal cycle times ............................................................................................................................ 36
10.2 Power supply ......................................................................................................................................... 36
10.3 Output .................................................................................................................................................... 37
10.3.1 Fan connector .................................................................................................................................... 37
10.4 Control signals ....................................................................................................................................... 38
10.4.1 Sensor connector M12 ....................................................................................................................... 38
10.4.2 D-Sub15 control interface .................................................................................................................. 39
10.4.3 D-Sub9 power setting interface (optional, DN750-1850).................................................................... 40
10.5 Ambient conditions ................................................................................................................................ 41
10.5.1 Operation ........................................................................................................................................... 41
10.5.2 Storage .............................................................................................................................................. 41
11 Standard Warranty .................................................................................................................. 42