manualshive.com logo in svg

Maurer DN1100, Перевод из оригинального руководства, Страница: 13 / 43

Поделиться
Скачать
Maurer DN1100 Скачать руководство пользователя страница 13

 

I n s t a l l a t i o n  

Power Module  DN 

Version 09.2019  

Page 13/43 

4 

Installation 

Mount device on and flat ground, stable and flat surface.  

•

  Ensure safe operation of device at all times  

•

  Operate power module only upright. 

Do not operate in horizontal position

. 

 
Connection and disconnection of the coil module only with main switch off.  
 
Installation and commissioning of the device only by skilled personell.  

•

  Connect only to power source with correctly installed protection conductor 

•

  Connect with regard to local regulations 

 
Improper connection can damage the machine.  

•

  Installation with off-state power source 

•

  Installation with main switch off 

 
Interface signals maximal current load 100mA 
D-Sub15 PIN14/15: 0...10 VDC Output maximal current load 1 mA 
 
Do not connect D-Sub interface with computer interface verbinden.  Pc and power 
module may be damaged.  
 

4.1  Transport 

 
Do not lift components of more than 25 kg by hand.  
 
Do not lift coils mounted in shielding chambers on the shielding chamber.  

•

  Lift with support from below 

 

Power module can be lifted and transported by two persons. 

4.2  Installation process 

•

  Mounting of coil 

•

  Mounting of power module 

•

  Check  fastening torque of power connections 

•

  Connection power supply power module 

•

  Connection 

Coil module connector

 and 

Coil module monitoring M8

 

•

  Connection 

Fan connector 

 (if applicable; MM VE) 

•

  Optional: Connection 

D-Sub15 Control Interface

 

•

  Optional: Connection 

Power selection interface D-Sub9

 (DN750-1850) 

•

  Optional: Connection photo sensor on 

Sensor connector M12 

 

 

Содержание DN1100












































Отзывы:

Нет отзывов