Maurer DN1100 Скачать руководство пользователя страница 37

 

S p e c i f i c a t i o n s  

Power Module  DN 

Version 09.2019  

Page 37/43 

10.3 Output 

 

DN150 

DN750 

DN1100 

DN1850 

Voltage max 

5

 

6

 

1-phase, 230 VAC 

1-phase, 400 VAC 

Nominal power 

7

 

1.5 kW 

7.5 kW 

11 kW 

18.5 kW 

Nominal max. current RMS 

8

 

14 A for 0.5s 

25.5 A for 1s 

37.5 A for 1s 

57 A for 1s 

Nominal  max.  power  (at  230/400VAC 
supply current) 

2.8 kVA for 0.5s 

12 kVA for 3 s 

17 kVA for 3 s 

26 kVA for 3 s 

Table 11: Ausgang 

10.3.1  Fan connector  

 

DN150 (optional) 

DN750-1850 

Voltage range 

220…240VAC (50/60Hz)

9

 

0…24 VDC 

Fuse protection 

10A 

4A 

Connector: 

Phoenix Contact SACC-E-MINFS-3CON-PG13/0,5 

Phoenix Contact SACC-E-MINFS-5CON-PG13/0,5 

Table 12: Fan connector  

     

 

Figure 10: Configuration Fan connector DN150 (left) / DN750-1850 (right) 

Configuration 

PIN 

DN150 

DN750-1850 

PE 

- (not connected) 

0V 

PE  

- (not available) 

+24V 

- (not available) 

- (not connected) 

Table 13: PIN-configuration 

 

 

 

Output voltage subject to parameterisation. Noted values correspond to maximal values.

  

6

 

The maximum output voltage can’t exceed the supply voltage 

7

 At 100% duty cycle 

At 230/400VAC supply current. Reduced current/power with lower supply voltages

 

9

 Corresponds to supply voltage/frequency 

Содержание DN1100












































Отзывы: