Masoneilan SVI II ESD Скачать руководство пользователя страница 78

Страница: 78 / 220

BHGE

Analog with Discrete Safety Demand (A/DSD)

The Analog with Discrete Demand configuration is: 4 - 20 mA power input with superimposed
HART

communications for control system and 24 VDC 2 wire for Safety System (Figure 53).

Figure 53 Analog with Discrete Safety Demand (A/DSD) Configuration

HART

Wiring Guidelines

In order for the SVI II ESD to communicate, the SVI II ESD must be physically connected to a
HART

compliant network. “Connecting to the Control Loop” outlines wiring the SVI II ESD.

Connecting to the Control Loop

The SVI II ESD PST controller

MUST BE

grounded according to local regulations. It is important

to maintain correct polarity at all times, otherwise the PST controller may not operate
properly. Physically connect the SVI II ESD to the HART

loop using a cable specified by Field

Comm

. A shielded cable is recommended.

To connect the Control Loop to the SVI II ESD:

1. Connect one end of the cable to the control loop's 4 - 20 mA output.

2. Remove the threaded wiring covers on the PST controller.

3. Connect the other end of the cable to the SVI II ESD. There are two threaded openings on

the PST controller. Use the opening with the red plastic insert.

4. Maintain po and - respectively.

NOTE

Position Retransmit: when wiring this feature:

Wire using the same gauge wire as for the 4-20 mA control loop.

In general, ensure that it is connected to the control system’s
analog systems card.

Ensure the control loop is powered when using a meter to make
any measurements.

SVI II ESD

Setpoint 4- 20 mA+ HART

4 Wire Solution -Safety Function Triggered by Discrete 0 - 24 VDC Signal (3VDC = Safety Trip)

Control System

Safety System

Safety Trip Signal Discrete 3 VDC- 24 VDC

or Safety System

Содержание SVI II ESD




























































































































































































































Результаты поиска

Содержание SVI II ESD

Отзывы:

Бренды по названию

Популярные бренды

Masoneilan SVI II ESD, Руководство по установке и обслуживанию

Результаты поиска

Содержание SVI II ESD

Отзывы:

Бренды по названию

Популярные бренды