Masoneilan SVI II ESD Скачать руководство пользователя страница 149

Страница: 149 / 220

Masoneilan SVI II ESD Installation and Maintenance Manual

149

BIAS_OUT_
OF_RANGE

Yes/No

No/Yes

Bias Out
Of Range

The servo signal
to the cur-
rent-to-pressure
converter is out-
side of normal
throttling range.

Ensure the
positioner is in
Normal mode
and air supply
is sufficient. If it
is, the
I/P converter
may be failing.

Replace the
positioner.

IP_OUT_OF_
RANGE

Yes/No

I/P Out
Of Range

1- The loop cur-
rent to the inter-
nal
current-to-pres-
sure converter is
outside of normal
range.

Ensure the
positioner is in
Normal mode
and air supply
is sufficient. If it
is, the
I/P converter
may be failing.

Replace the
positioner.

TEMPR_
OUT_OF_
RANGE

Yes

Yes/No

No/Yes

Temp.
Out Of
Range

The board tem-
perature is below
-40 °C or above
85 °C.

NOT IMPLE-
MENTED

FACTORYWRITE

NA/NA

No/Yes

Reserved
(2-3)

NOT IMPLE-
MENTED

Undefined
(reserved)

NA/NA

No/No

Reserved
(2-4)

NOT IMPLE-
MENTED

Undefined
(reserved)

NA/NA

No/No

Reserved
(2-5)

NOT IMPLE-
MENTED

Undefined
(reserved)

NA/NA

No/No

Reserved
(2-6)

NOT IMPLE-
MENTED

Undefined
(reserved)

NA/NA

No/No

Reserved
(2-7)

NOT IMPLE-
MENTED

NVM_
CHECKSUM

No/No

Yes/Yes

NVM
Check-
sum
Error

1- A permanent
corruption of the
content in
non-volatile
memory
occurred.

1- Remove power
to the device for 2
minutes and
restart the device.
2- If the failure
persist, replace
the device.

Table 13 SVI II ESD Fault Matrix (Continued)

Sequence

Byte

Bit

FAULT Name

Criticality

of Alarm

Auto-
mati-

cally

cleared

Can be

cleared/

Persists

across

resets

Non-
Mas-

kable/

Annunci-

ated

TEXT For

DD &

ValVue

ESD2

English

Probable Cause

English

Recommended

Action

Содержание SVI II ESD




























































































































































































































Результаты поиска

Содержание SVI II ESD

Отзывы:

Бренды по названию

Популярные бренды

Masoneilan SVI II ESD, Руководство по установке и обслуживанию

Результаты поиска

Содержание SVI II ESD

Отзывы:

Бренды по названию

Популярные бренды