Masoneilan SVI II ESD Скачать руководство пользователя страница 150

Страница: 150 / 220

150

BHGE

RAM_
CHECKSUM

Yes/No

Yes/Yes

RAM
Check-
sum
Error

1- A corruption of
the content in vol-
atile memory
occurred.

1- Notify factory
at svisup-
[email protected].

FW_
CHECKSUM

No/No

Yes/Yes

Flash
Check-
sum
Error

1- Invalid firm-
ware checksum
due to data cor-
ruption.

1- Remove power
to the device for 2
minutes and
restart it.
2- If the failure
persists, Replace
device.

STACK

Yes/No

Yes/Yes

Stack
Error

1- A problem with
the memory stack
occurred.

1- Clear the condi-
tion using ValVue
ESD or HART

Host.

FACTORYMODE 1

Yes/No

Factory
Mode
Fault

1- Device is in the
factory mode.

1- Replace device
and report the
problem at svi-
sup-
[email protected].

NVM_TEST

Yes/No

Yes/Yes

NVM Test
Error

1- A problem
occurred when
testing non-vola-
tile memory.

1- 1- Clear the
condition using
ValVue ESD or
HART

Host.

LATCH_FSAFE

Yes/Yes

No/Yes

Reserved
(3-6)

Undefined
(reserved)

NA/NA

Yes/No

Reserved
(3-7)

REF_
VOLTAGE

Yes/No

Ref Volt-
age Fault

1- A component
problem is affect-
ing the circuit
board's reference
voltage.

1- Replace the
device and report
problem at svi-
sup-
[email protected].

POSITION_
SENSOR

Yes/No

Position
Sensor
Fault

1- Electronic hall
sensor compo-
nent and related
components
failed.

1- Replace device
and report prob-
lem at svisup-
[email protected].

CURRENT_
SENSOR

Yes/No

Current
Sensor
Fault

1- Electronic input
loop current sen-
sor is damaged.

1- Replace device
and report prob-
lem at svisup-
[email protected].

TEMPERATURE_
SENSOR

Yes/No

Yes/Yes

Tem-
perature
Sensor
Fault

1- Electronic tem-
perature sensor is
damaged.

1- Replace device
and report prob-
lem at svisup-
[email protected].

Table 13 SVI II ESD Fault Matrix (Continued)

Sequence

Byte

Bit

FAULT Name

Criticality

of Alarm

Auto-

mati-

cally

cleared

Can be

cleared/

Persists

across

resets

Non-
Mas-

kable/

Annunci-

ated

TEXT For

DD &

ValVue

ESD2

English

Probable Cause

English

Recommended

Action

Содержание SVI II ESD




























































































































































































































Результаты поиска

Содержание SVI II ESD

Отзывы:

Бренды по названию

Популярные бренды

Masoneilan SVI II ESD, Руководство по установке и обслуживанию

Результаты поиска

Содержание SVI II ESD

Отзывы:

Бренды по названию

Популярные бренды