Masoneilan SVI II ESD Скачать руководство пользователя страница 139 | Manualshive

Страница: 139 / 220

Masoneilan SVI II ESD Скачать руководство пользователя страница 139

Masoneilan SVI II ESD Installation and Maintenance Manual

=

|

139

© 2017 Baker Hughes, a GE company, LLC. All rights reserved.

Installing the SVI II ESD Display Cover

NOTE

After replacing the SVI II ESD Display Cover you must power up
the unit (see “Powering Up the SVI II ESD” on page 80).

The replacement display cover is shipped with a lanyard to prevent the cable (that connects
from the display to the Terminal Board) from breaking. The lanyard must be inserted under
the screw in the lower left corner, that attaches the terminal board to the SVI II ESD housing.

To Install the cover:

1. Install the lanyard and tighten the screw to 5 in/lb.

2. Using the 3 mm hex key, remove the screw from the lower left corner, connecting the

terminal board to the SVI II ESD housing.

3. Connect the cable from the display into the LCD connector on the terminal board.

4. Ensure that the gasket is in its groove in the housing.

5. Place the cover over the screw mounts.

6. Tighten the four screws with the 5 mm hex key.

7. After installing the new display you must power up the unit (refer to

“Powering Up the SVI

II ESD” on page 80

NOTE

The cover of SVI II ESD is a critical component for safety in
Hazardous Areas. To ensure safe operation the flat surfaces of the
cover and the housing must be clean and absolutely free of
particles or dents. There must be no gap between the housing and
cover; torque spec is 50 in/lb.

Ensure that:

Gasket is seated in the groove in the housing flange.

No wires or retaining cable can be trapped under the cover flange.

Flange area is not corroded and surface is not scarred.

Four cover bolts are securely tightened to 50 in/lb.

«
...
137
138
139
140
141
...
»

Содержание SVI II ESD





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды