manualshive.com logo in svg

Masoneilan SVI II ESD, Руководство по установке и обслуживанию

Поделиться
Скачать
Masoneilan SVI II ESD Скачать руководство пользователя страница 178

© 2017 Baker Hughes, a GE company, LLC. All rights reserved.

178 

| 

BHGE

SVI II ESD Setups

Control systems using Explosion Proof or Conventional I/O Systems must have a compliance 
voltage greater than 9 V at 20 mA.

Control systems using Intrinsic Safety methods must have a compliance voltage greater than 
17.64 V.

For General Purpose and Explosion Proof (EEx d) Installation Schematic see Figure 82 on 
page 179. For intrinsically safe installation schematic see Figure 83 on page 180. The SVI II 
ESD positioner can be located in a general-purpose or hazardous area protected by Explosion 
Proof (EEx d) methods. Wiring diagrams are generalized, actual wiring must adhere to 
Electrical Installation section of manual and local electrical codes. The use of a Hand-held 
Communicator or a HART

®

 modem is not permitted in the Hazardous Area protected by 

Explosion Proof (EEx d) methods. In Figure 83 on page 180 the SVI II ESD positioner is located in 
a hazardous area protected by Intrinsically Safe wiring practices.

The SVI II ESD requires an electrical input from a 4 - 20 mA current source. SVI II ESD’s input 
signal can carry a HART

®

 communication protocol signal from ValVue ESD or other software 

and a HART

®

 modem, or from a HART

®

 Hand-held Communicator. Since the source of the 

input signal from the process control system is located in a non-hazardous location, setup 
requires an intrinsic safety barrier be placed between the process control system and the SVI II 
ESD. If the SVI II ESD is located in a hazardous area with Intrinsically Safe protection a barrier is 
not required for a flameproof installation. Alternatively the system can be installed as 
Explosion Proof 

⁄

 flameproof.

The SVI II ESD can communicate with a remote PC running ValVue ESD software via a 
dedicated HART

®

 modem connected to PC's serial port. The PC, which is not intrinsically safe, 

must be connected to the circuit on the safe area side of the intrinsic safety barrier when the 
valve is located in a hazardous area.

The SVI II ESD can be operated, calibrated, configured either by using local pushbutton and 
display, using a remote PC running ValVue ESD software or with the HART

®

 Hand-held 

Communicator. The HHC475 HART

®

 Hand-held Communicator is approved for Intrinsically 

Safe use in accordance with FM, CSA, and ATEX standards. Read and observe all HHC labeling. 
The SVI II ESD is polarity sensitive so that the positive lead must be connected to the positive 
(+) terminal and the negative lead must be connected to the negative (-) terminal. 

Reversing 

polarity will not cause damage but the unit will not function properly.

Содержание SVI II ESD





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды