Masoneilan SVI II ESD Скачать руководство пользователя страница 177

Страница: 177 / 220

Masoneilan SVI II ESD Installation and Maintenance Manual

177

HART

Wiring Guidelines

The following list contains eight guidelines for a successful implementation of DC current
signal, DC power, and HART

communication to the SVI II ESD:

Compliance voltage at the SVI II ESD must be 9 V at the maximum current of 20 mA.
See “Determining an SVI Positioner Compliance Voltage in a Control System” on
page 217.

Signal to the SVI II ESD must be a well-regulated current in the range of 3.8 to 22 mA.

Controller output circuit must be unaffected by the HART

tones which are in the

frequency range between 1200 and 2200 Hz.

Frequency range of the HART

tones must have a circuit impedance of more than 220

Ohms, typically 250 Ohms.

HART

tones can be imposed by the positioner to a communication device located

anywhere on the signaling circuit.

Capacitance of the signaling circuit can not exceed about 0.26 microfarads or with
high series resistance 0.10 microfarads.

Cabling must be shielded to prevent electrical noise that would interfere with HART

tones, with grounded shield at only one location.

Position Retransmit: when wiring this feature:

Wire using the same gauge wire as for the 4-20 mA control loop.

In general, ensure that it is connected to the control system’s analog systems card.

Ensure the control loop is powered when using a meter to make any
measurements.

NOTE

For details and calculation methods for wiring resistance, and
capacitance and for calculation of cable characteristics refer to
the HART

FSK Physical Layer Specification.

Содержание SVI II ESD




























































































































































































































Результаты поиска

Содержание SVI II ESD

Отзывы:

Бренды по названию

Популярные бренды

Masoneilan SVI II ESD, Руководство по установке и обслуживанию

Результаты поиска

Содержание SVI II ESD

Отзывы:

Бренды по названию

Популярные бренды