Masoneilan SVI II ESD Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 220

Masoneilan SVI II ESD Скачать руководство пользователя страница 112

© 2017 Baker Hughes, a GE company, LLC. All rights reserved.

112

|

BHGE

VIEW DATA Menu

The VIEW DATA menu reads current configuration information, including PST configuration.
This information cannot be changed from the VIEW DATA menu. Exit from the VIEW DATA
menu to return to the previous menu.

This menu can be entered either from the MANUAL Mode menu or from NORMAL Mode menu.

When entering VIEW DATA from NORMAL mode the valve shall still respond to changes in set
point input signal and the displayed values change in accordance with input signal changes.
When entered from MANUAL mode, the valve is in locked position. The parameters viewable
by pressing

+

and

-

are:

SINGLE

ATO or ATC

PSI, BAR, KPA

Viewing Configuration Parameters

To view configuration parameters use the following procedure:

1. If in NORMAL operating mode, press any button.

2. Press

+

to move through options until you reach the VIEW DATA menu item.

3. Press

*

to go to VIEW DATA menu (This leaves the valve in NORMAL mode.). If in MANUAL

mode, press

+

repeatedly until the VIEW DATA menu item is reached. Press

*

to select

VIEW DATA mode.

4. To exit from the VIEW DATA menu, press

*

at any menu line. You return to the last

displayed menu.

«
...
110
111
112
113
114
...
»

Содержание SVI II ESD





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды