UK: Martindale Automatic Welding Helmet 9/13 User Instructions
FR: Casque de soudage automatique (Teinte 9/13)
– Mode d’emploi
ES: Instrucciones de casco para soldar automático 9/13
DE: Automatischer Schweißhelm 9/13
– Gebrauchsanleitung
024-001-783 REV A 03/17 Pag
e
6 of 39 M23AWH/13
Centurion Safety Products Ltd. Howlett Way, Thetford, Norfolk, IP24 1HZ, UK
Tel. 0044 (0)1842 754266 Fax. 0044 (0)1842 765590
Summary
The automatic welding mask is a new generation product for labour protection. Some new and high science and technology such
as LCD
,
optoelectronics detection, solar power, microelectronics, etc are integrated into it. The automatic welding mask not only
can efficiently protect operators’ eyes from injuries caused by arc, but also can make both hands free and strike arc accurately.
Therefore, the quality of products and work efficiency may be raised considerably. lt may be widely used for various welding, cutting,
spraying and arc gouging, etc.
WARNING
Read and understand all instructions before using.
•
Be sure that the dark shade of the lens in the welding helmet is the correct shade number for your application.
•
This helmets and lenses are not suitable for “overhead” welding application, laser welding, or laser cutting applications.
•
Welding helmets are designed to protect the eyes and face from sparks, spatter, and harmful radiation under normal welding
conditions.
•
This helmet will not protect against explosive devices or corrosive liquids. Machine guards or eye splash protection must be
used when these hazards are present.
•
Impact resistant, primary eye protection, spectacles or goggles that meet current ANSI specifications, must be worn at all times
when using this welding helmet.
•
Avoid work positions that could expose unprotected areas of the body to spark, spatter, direct and/or reflected radiation. Use
adequate protection if exposure cannot be avoided.
•
Check for light tightness before each use. Before each use, check that the protection plates are clean and that no dirt is covering
the sensors on the front of the lens.
•
Inspect all operating parts before each use for signs of wear or damage. Any scratched, cracked, or pitted parts should be
replaced immediately.
•
Do not make any modifications to either the welding lens or helmet, other than those specified in this manual. Do not use any
replacement parts other than those specified in this manual, Unauthorized modifications and replacement parts will void the
warranty and expose the user to the risk of personal injury.
•
If this lens does not darken when striking arc, slop welding immediately and contact representative.
•
Do not immerse this lens in water if this model is not water proof.
•
Do not use any solvents on any lens or helmet components.
•
The recommended operating temperature range for welding lens is -10°C-65°C (14°F-149°F). Do not use this device beyond
these temperature limits.
Failure to follow these warnings and/or failure to follow all of the operating instructions could result in severe personal injury.
Characteristics
M23AWH 9/13 automatic welding helmet is equipped with a filter set that can become dark. The filter is transparent before welding,
so the operators may observe the work surface clearly. When striking arc, the filter darkens automatically immediately. When arc
goes out, the filter will become transparent again. The switching time from light to dark is about 0.08ms. The switching time from
dark to light may be set up within 0.1-0.9 second.
The mask is equipped with continuous darkness adjusting unit, so the operator may select an arbitrary dark shade number ranging
from 5-13.
M23AWH 9/13 automatic welding mask gives the operators permanent complete protection against UV/IR even in transparent
condition. The UV/IR protection level is up to DIN15 in all time. The power is provided by solar cells and replaceable battery.
The mask is equipped with 4 sets of photosensors to sense arc light. In addition, the mask is also provided with an outer protection
plate made of high polymer materials. The plate is wear-resistant, thermostable, and has no dregs-sticking, thus a very long service
life.
