manualshive.com logo in svg

Market Forge Industries STP-6G, Инструкция по установке и эксплуатации, Страница: 50 / 52

Поделиться
Скачать
Market Forge Industries STP-6G Скачать руководство пользователя страница 50

6. Maintenance 

 

 

 

Table 6.12 - Chassis 

Assembly Parts List 

ITEM

 

QTY.

 

DESCRIPTION 

PART NO.

 

1

 

1

 

Blower Box Assembly

 

see Figure 6.9 

2

 

1

 

Blower Box Support Bracket

 

E91-5739

 

3

 

1

 

Gas Valve Support Assembly

 

see Figure 6.11 

4

 

2

 

Pressure Switch*

 

E08-6502

 

5

 

2

 

Strip Heater

 

E08-6503

 

6

 

1

 

Tempering Tank Assembly

 

see Figure 6.10 

7

 

2

 

Thermostat, Surface Mount, N.O., close at 170°F

 

E09-6428

 

8

 

4

 

Threaded Stand-off, 6-32, hex, 1/2" long, zinc plated

 

E08-3498

 

9

 

6

 

1/4-20 Hex Head Machine Screw, 7/8" long, zinc plated

 

E08-3491

 

10

 

4

 

1/4-20 Nyloc Hex Nut, zinc plated

 

E08-3842

 

1 1

 

4

 

1/4" Flat Washer, zinc plated

 

E08-4012

 

12

 

4

 

4-40 Slotted Pan Head Machine Screw, 1 1/4" long, zinc plated

 

E08-3497

 

13

 

4

 

4-40 Nyloc Hex Nut, zinc plated

 

E08-3845

 

14

 

4

 

#4 Flat Washer, zinc plated

 

E10-1747

 

15

 

4

 

8-32 Hex Nut, zinc plated

 

E08-3840

 

16

 

6

 

#8 Split Washer, zinc plated

 

E08-4009

 

17

 

4

 

#8 Flat Washer, zinc plated

 

E08-4008

 

18

 

4

 

10-32 Slotted Truss Head Machine Screw, 1/2" long, zinc plated

 

E08-3486

 

 

* IMPORTANT: Note the 

individual locations of each pressure switch! (See 

Figure 6.12 on page 6.26.) 

• The 

pressure switch that controls the BOTTOM cooking compartment system is on the 

LEFT as viewed from the front of the unit. 

• The 

pressure switch that controls the TOP cooking compartment system is on the

 

RIGHT, as 

viewed from the front of the unit. 

MARKET 

FORGE 

INDUSTRIES, INC. 

35 GARVEY STREET EVERETT, MA 02149 

 

 

6.27

 

TEL: 6 17 387 4100 TELEX: 94-94 1 4 

FAX: 617 387 4456 OUTSIDE MA 800 227 2659 

 

Содержание STP-6G





















































Отзывы:

Нет отзывов