manualshive.com logo in svg

Market Forge Industries STP-6G, Инструкция по установке и эксплуатации, Страница: 21 / 52

Поделиться
Скачать
Market Forge Industries STP-6G Скачать руководство пользователя страница 21

5. Troubleshooting 

 
 
 
 
 

                   TROUBLE                                               POSSIBLE CAUSE                                                      REMEDY

 

Generator will not create steam 

(Main Burner will not ignite, STEAM 
ON light does not come on).

 

1. Cooking compartment door is ajar.

 

2. Cooking compartment door out of 

alignment.

 

1. Check to be sure that the cooking 

compartment door is closed and 
latched.

 

2. Check to be sure cooking 

compartment door is properly aligned.

 

 

 

3. Faulty door magnet or magnetic reed switch.

 

3. Check magnet and reed switch. 

Replace if necessary.

 

 

 

4. Faulty ignition/flame sensor control module,

 

4. See 

Ignition/Flame Sensor Control 

Diagnostic

 section.

 

 

 

5. Faulty ignitor.

 

5. * Check electrical connections.  

* Be sure ignitor gap is 1/8".  

* Check ignitor allignment.  

* Be sure ignitor is seated properly in its   

mounting.

 

 

 

6. Faulty Main burner solenoid on gas regulator 

valve relay.

 

6. Check Main burner solenoid relay. 

Replace if necessary.

 

 

 

7. Faulty Main burner solenoid on gas regulator 

valve.

 

7. If 24 volts is verified at the solenoid 

coil, but valve fails to open, replace gas 

regulator.

 

 

 

8. Faulty pressure switch.

 

8. Check/replace pressure switch if 

necessary.

 

 

 

9. Faulty control panel TIMER

 

9. Check/replace control panel TIMER if 

necessary.

 

 

 

10. Faulty MODE SELECT Switch.

 

10.Check/replace MODE SELECT 

switch if necessary.

 

 

 

11. Faulty CONSTANT STEAM Button.

 

11 .Check/replace CONSTANT 

STEAM button if necessary.

 

 

 

 

 

 

 

MARKET FORGE INDUSTR IES

, 

INC

. 

35 

GARVEY 

STREET EVERETT, MA 02149 

 

 

            

5.3

 

TEL: 6 17 387 4100 TELEX: 94-94 1 4 
FAX: 6 1 7 387 4456 OUTSIDE MA 800 227 2659 

 

Содержание STP-6G





















































Отзывы:

Нет отзывов