manualshive.com logo in svg

Market Forge Industries STP-6G, Инструкция по установке и эксплуатации, Страница: 35 / 52

Поделиться
Скачать
Market Forge Industries STP-6G Скачать руководство пользователя страница 35

   

 

The cooking compartment door alignment, door 

handle tension and latch tension are pre-adjusted at 

the factory during assembly. During normal usage, 
these should not need any attention. 

Note that when the cooking compartment doors 

are reversed, as described in Section 2.5 , the doors 
will need to be aligned and the door latch tension will 
need to be adjusted (the door handle will not need 
adjustment when the door is reversed). 

 
6.8.1 Door Alignment

 

The cooking compartment doors are pre-aligned 

at the factory during assembly, and should not need 
adjusting unless they are reversed. Should the doors 

need realignment, the procedure is as follows: 

Procedure:

 

1. Open the cooking compartment door. 

2. Loosen all 4 bolts  (2 per hinge) which mount the 

upper and lower hinge brackets to the face of 
the unit using a 5/1 6" wrench. DO NOT 
REMOVE THE BOLTS. 

3. Begin to retighten all 4 bolts so that they are snug 

against the face of the unit. DO NOT 

COMPLETELY TIGHTEN THE BOLTS. 

4. Slowly, ease the cooking compartment door 

dosed until it is latched. 

5. The cooking compartment door can now be 

raised, lowered, and/or rotated into position by 
bumping it with the palm of your hand or by 
using a small rubber mallet. 

6. First, check the alignment at the front of the door 

by making sure that the striker in the door is 
centered, with the latch mechanism on the front 
of the unit. 

7. Square the door to the unit by raising or 

 

 

 

lowering the hinge side of the door, keeping the latch 
centered with the striker.

 

8. Visually inspect the door. Be sure that the door is square 

to the unit, the striker is centered with the latch, and 
the gasket is in contact with the entire lip of the 
cooking compartment.

 

9. Gently open the cooking compartment door, taking care 

not to move it out of position.

 

10. Tighten all 4 door hinge bracket mounting bolts, using 

a 5/16" wrench.

 

11. Clos

e

 and visually inspect the door again, as described 

in step 8.

 

6.8.2 Door Latch Tension Adjustment

 

The cooking compartment door latch tension is 

preset at the factory, and should not need adjusting 
unless the doors are reversed. Should the latch need 
adjustment, the procedure is as follows: 

Procedure:

 

1. Open the cooking compartment door. 

2. If latch is mounted on the right side of the cooking 

compartment, remove the corresponding control 
panel. If latch is mounted on the left side of the 
cooking compartment, remove left side panel. 

3. Tighten both nuts down until the springs are fully 

compressed. 

4. Back each nut off 1/2 turn. 

5. Remount the control panel or left side panel. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MARKET FORGE INDUSTRIES, INC. 

35 GARVEY STREET 

EVERETT

, MA 02149 

 

 

6.12 

TEL: 617 387 4100 TELEX: 94-94 1 4 

FAX: 6

 17

 387 4450 OUTSIDE MA 800

 227

 2859 

6. Maintenance

 

 

Содержание STP-6G





















































Отзывы:

Нет отзывов