manualshive.com logo in svg

Market Forge Industries STP-6G, Инструкция по установке и эксплуатации, Страница: 16 / 52

Поделиться
Скачать
Market Forge Industries STP-6G Скачать руководство пользователя страница 16

 

4. Operation 

 
 
 
 
 
 

Power Switch 

Located at the bottom of the control panel. Pressing this switch into the ON position will 

supply power to unit and activate the corresponding system. Pressing this switch into the 
OFF position will cut off power to the corresponding system and shut down the unit.

 

Power Indicator

 

Located in the body of the POWER SWITCH. Lights up red when the POWER SWITCH Is 

pressed into the ON position.

 

Ready Light

 

Located above the POWER SWITCH. Lights up green when the corresponding generator 

has warmed up, indicating that it is ready to create steam.

 

Mode Selector Switch

 

Located in the center of the control panel, just above the ready light. Turn the switch to the 

right to select the STEAM mode. Turn the switch to the left to select the STEAM & HOLD 
mode.

 

Timer Knob

 

Located near the top of the control panel. Turn the timer knob clockwise to set the cook 

time

.

 

Steam On Indicator

 

Located near the top of the control panel. Lights up green when any cooking mode is 

active.

 

Steam Demand Indicator

 

Located above the Steam On indicator. Lights up red as the product you are cooking calls 

for steam. It will cycle on and off at varying rates depending on the quantity and product 
being cooked.

 

Hold Indicator

 

Located near the center of the control panel, on the left side. Lights up amber when the 

unit is in the HOLD mode.

 

Temperature Gauge

 

Located on the right side of each of the steam hoods, above the control panel. They are 

used to monitor the internal temperature of the cooking compartments during the HOLD 
mode.

 

Constant Steam Switch

 

Located near the center of the control panel, on the right side. Press the button once to 

engage it and enter the CONSTANT STEAM mode. Press it again to disengage it and exit 

the CONSTANT STEAM mode.

 

Constant Steam Indicator

 

Located next to the Constant Steam button. Lights up green whenever the unit Is in the 

CONSTANT STEAM mode.

 

Clean Generator Warning 

Indicator

 

Located in the lower right side of the control panel. This will light up red when the 

generator needs to be de-limed.

 

 

Table  4.1  

Controls and Indicators

 

MARKET FORGE INDUSTRIES

, 

INC

. 

35 GARVEY STREET EVERETT, MA 02149 

 

 

           

4.3 

TEL: 6 17 387 4100 TELEX:  94-94 I 4 
FAX: 6 I 7 387 4456 OUTSIDE MA 800 227 2659 

Содержание STP-6G





















































Отзывы:

Нет отзывов