Market Forge Industries STP-6G Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 52

Market Forge Industries STP-6G Скачать руководство пользователя страница 19

5.1 GENERAL

The information in this section is intended to assist the

operator, maintenance and the service personnel in locating
the source of problems which may occur with the cooker.
Before following any of the procedures given in this section,
the operator/maintenance person should be thoroughly
familiar with the "Operation" Section of this manual.

If the problem cannot be readily corrected without the

use of tools, the operator/maintenance person should contact
the nearest Market Forge service agency for assistance.

TROUBLE POSSIBLE CAUSE REMEDY

POWER Light does not come on
when the POWER Switch is
pressed into the ON position.

1. No 120v power to unit.

2. Fuse blown.

3. Faulty POWER Switch.

1. Be sure 120v power supply is on.

2. Replace fuse.

3. Check/replace POWER Switch.

Water enters the steam generator
and/or tempering tank very slowly.

1. Dirty strainer screen in the water fill solenoid
valve.

2. Dirt or lime accumulation on seat of water fill
solenoid valve.

1. Clean/replace strainer screen.

2. Clean valve seat.

Steam generator will not fill.

1. Faulty generator fill solenoid valve. 2. Faulty
generator drain solenoid valve.

1. If 120 Volt is verified at the solenoid
coil, but the valve fails to open, replace
solenoid.

2. If 120 Volt is verified at the solenoid
coil, but the valve fails to close, replace
solenoid.

Tempering tank will not fill.

1. Fuse blown.

2. Faulty tempering tank fill/cool solenoid valve.

3. Faulty tempering tank drain solenoid valve.

1. Replace fuse.

2. If 120 Volt is verified at the solenoid
coil, but the valve fails to open, replace
solenoid.

3. If 120 Volt is verified at the solenoid
coil, but the valve fails to close, replace
solenoid.

MARKET FORCE INDUSTRIES, INC.

35 GARVEY STREET

EVERETT

, MA 02149

5.1

TEL: 617 387 4100 TELEX: 94-94 1 4

FAX: 6 17 387 4456 OUTSIDE MA 800 227 2659

5. Troubleshooting

«
...
17
18
19
20
21
...
»

Содержание STP-6G





















































Отзывы:

Нет отзывов