Market Forge Industries STP-6G Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 52

Market Forge Industries STP-6G Скачать руководство пользователя страница 33

6.7 CONTROL PANEL

ELECTRICAL SERVICE ACCESS

The control panel assembly is mounted onto the front

of the unit. It houses all of the controls and indicators which
are used to operate the Steam Tech Plus. In order to service
any of the control panel electrical componentry, the control
panel assembly must be removed from the front of the unit.

CAUTION:

Be sure to disconnect 120 volt power supply from

the unit and turn off the main gas supply before servicing

any

electrical componentry.

Procedure:

1. Remove the 4 screws that fasten the control panel

assembly onto the front of the unit.

2. Gently move the control panel assembly out

away from the unit.

NOTE:

Only move the control panel assembly out as far as

is necessary to access the rear of the assembly. PULLING
THE CONTROL PANEL OUT TOO FAR CAN CAUSE
DAMAGE BY PUTTING UNNECESSARY STRAIN ON
WIRES AND CONNECTIONS!

3. Separate the control panel housing and indicator light
mounting bracket by removing the 4 nuts which hold them
together. Be careful not to lose the 1/4-20 nuts which are
used as spac ers, (I -per stud). This will allow total access
to all controls and indicators for service, repair, or
replacement.

See Figure 6.3 on page 6.11

.

6.8 DOOR ADJUSTMENT

Table 6.3 -

Control Panel Assembly Parts

List

ITEM

QTY.

DESCRIPTION

PART NO.

I

1

Buzzer

El 0-6682

2

1

"Clean

Generator" Indicator Light (round neon, red)

E08-6530

3

1

"Constant Steam" Button

E08-6526

4

1

"Constant Steam" Indicator Light (round neon, green)

E08-6529

5

1

Control Panel Housing Assembly

E91-5743

6

1

Control Panel Light Mounting Bracket

E91-5688

7

1

"Hold"

Indicator Light (round neon, amber)

E08-6531

8

1

"Mode Select" Switch Assembly

E08-6525

9

1

"Power On" Indicator Light

E08-6523

10

1

"Power

On" Indicator Light Tinnerman Retainer Cli

p

E08-6523

11

1

Power Switch

E08-6524

12

1

"Ready*

Indicator Light (rectangular neon, green)

E08-6527

13

3

Round Indicator Light Retainer Clip

E08-6527

14

1

"Steam

Demand"

Indicator Light (rectangular neon, red)

E08-6528

15

1

"Steam On" Indicator Light (rectangular neon, green)

E08-6527

16

1

Terminal Block

E08-6518

17

1

Timer

El 0-6291

18

1

Timer Knob

E08-3826

19

1

Timer Mounting Nut

El 0-6291

20

4

1/4-20 Hex Nut, zinc plated

E08-3844

21

2

6-32 Nut with nylon insert, zinc plated

E08-3838

22

2

6-32 Slotted Pan Head Machine Screw, zinc plated, 1/2" long

E08-3484

23

4

8-32 Nut with nylon insert, zinc plated

E08-3839

MARKET FORGE INDUSTR IES

,

INC

.

35 GARVEY STREET EVERETT, MA 02140

6.10

TEL-: 617 387 4100 TELEX: 34-9414

FAX: 617 387 4456 OUTSIDE MA 800 227 2659

«
...
31
32
33
34
35
...
»

Содержание STP-6G





















































Отзывы:

Нет отзывов