manualshive.com logo in svg

Market Forge Industries STP-6G, Инструкция по установке и эксплуатации, Страница: 38 / 52

Поделиться
Скачать
Market Forge Industries STP-6G Скачать руководство пользователя страница 38

6. Maintenance 

 
 
 
 

Table 6.5 - Cooking Compartment Door 

Assembly Parts List 

 

 

ITEM 

QTY 

DESCRIPTION 

PART NO. 

1 

1 

 

Door Gasket 

E91-5286 

2 

1 

 

Door Gasket Mounting Plate 

E91-5731 

3 

1 

Door Handle 

E91-5745 

4 

1 

 

Door Insert 

E91-5766 

5 

1 

 

Door Shell 

E91-5729 

6 

2 

Hinge Bearing, nylon 

E08-2702 

7 

1 

 

Hinge Bracket, Bottom (smaller) 

E91-5436 

8 

1 

 

Hinge Bracket, Top (larger) 

E91-5437 

9 

2 

Magnet 

E08-5027 

10 

2 

Magnet Retainer Bracket 

E91-5901 

11 

2 

Spring 

E08-4600 

12 

1 

Striker, Cast 

E09-1608 

13 

4 

Washer, Nylon 

E10-0100 

14 

2 

6-32 Nut with Nylon insert, zinc plated 

E08-3838 

15 

4 

10-32 hex head machine screw, 7/8" long, stainless steel 

E08-3488 

16 

2 

10-32 phillips flat machine screw, 1/2" long, stainless steel 

E08-3486 

17 

6 

10-32 slotted truss head machine scre w , 1/2" long, stainless steel 

E10-1764 

18 

6 

10-32 slotted truss head machine screw, 3/4" long, stainless steel 

E10-1765 

19 

4 

10-32 Nut with nylon insert, zinc plated 

E08-3841 

 
 

 

 

The cooking compartment door gaskets are made of a 

silicone type rubber material, which is very durable, but is 

subject to wear during normal daily operation. This gasket 

may start to leak which will cause the steamer to malfunction. 

Should the gasket begin to leak, it should be replaced. 

Procedure:

 

1. Open the cooking compartment door. 

2. Remove the 6 screws from the door gasket mounting 

plate on the inside of the door. 

3. Remove the door gasket mounting plate and the door  
    gasket. 

 

 

 

 

4. Install new door gasket (Market Forge Part Number 91 -

5286) into the door. 

5. Refasten the door gasket mounting plate to the inside of 

the door using the 6 screws. 

NOTE: Remember that the lip on the door gasket 

mounting plate must fit into the channel on the inside 

edge of the gasket for a proper seal. 

 
 

MARKET 

FORGE

 INDUSTRIES

, 

INC

 

35 GARVEY STREET EVERETT.MA 02149 

 

 

 

6.15 

TEL 6173874100 TELEX 94-9414 

FAX 6173874456 OUTSIDE MA 800 227 2659

 

 

Содержание STP-6G





















































Отзывы:

Нет отзывов