Maple Systems BLU300 Series Скачать руководство пользователя

Страница: 18 / 141

Mount the OIT to the Panel

STEPS:

1. Prepare the four screw clamps for the BLU300 by inserting the clamps into the slots of the back

enclosure as show in the illustration above.

2. Snap the OIT into the panel cutout using the plastic brackets of the back enclosure. Make sure that all

metal clamps are properly in position.

3. Tighten the screw clamps until all are uniformly snug.

CAUTION: Do not over-tighten the screws beyond snugness, or you may damage the housing.
REINSTALLATION: Because the gasket will take a “set” to the panel, be sure to reinstall the OIT to the same panel cutout

when a NEMA 4 seal is required. For best results, also replace the gasket itself.

Configuration Wiring

The OIT must be configured for a particular protocol before use. The

BlueLeaf

software (used on a PC with Windows 95 or

higher) is used for configuring the OIT. For detailed instructions on installing and using the software, please refer to the

software documentation section of this manual.

Connect the OIT to the PC for Configuration

To configure the OIT using Maple System’s configuration software, you will need the OIT Configuration Cable, Maple P/N

7431-0102. Connect the end marked “HMI” into the RS-232 port on the OIT and connect the end marked PC into the proper

1010-0300, Rev 02

Blue Series Installation & Operation Manual

Installing the Screws on the OIT

Содержание BLU300 Series














































































































































Результаты поиска

Содержание BLU300 Series

Отзывы:

Похожие инструкции для BLU300 Series

Бренды по названию

Популярные бренды

Maple Systems BLU300 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание BLU300 Series

Отзывы:

Похожие инструкции для BLU300 Series

Бренды по названию

Популярные бренды