22
ENGLISH
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed before
attempting to perform inspection or maintenance.
CAUTION:
Clean out the upper and lower guards
to ensure there is no accumulated sawdust which may
impede the operation of the lower guarding system.
A
dirty guarding system may limit the proper operation which
could result in serious personal injury. The most effective
way to accomplish this cleaning is with compressed air.
If
the dust is being blown out of the guards, be sure the
proper eye and breathing protection is used.
CAUTION:
After each use, wipe off the saw
dust on the tool.
Fine saw dust may come inside the
tool and cause malfunction or a fire.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
T o maintain prod uc t S A F ET Y and R EL I A BI L I T Y ,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Adjusting 0° -cut or 45° -cut accuracy
This adjustment has been made at the factory. But if it is
off, you can adjust it as the following procedure.
1.
L oosen th e c lamping sc rew s on th e f ront and rear
of th e tool so th at th e bev el angle c an be c h anged . S et
the stopper to -
bevel angle position if you are
going to adjust
-cut accuracy.
Fig.47:
1.
S topper
2.
Make th e base perpend ic ular or 4 5 ° to th e c irc ular saw
blade using a triangular rule by turning the adjusting screw with a
hex wrench. ou can also use a square rule to adjust angle.
Fig.48:
1.
T riangular rule
Fig.49 :
1.
Adjusting screw for angle
2.
Adjusting
sc rew f or 4 5 ° angle
3.
T igh ten th e c lamping sc rew s and th en make a test
c ut to c h ec k if d esired angle is obtained .
Adjusting the parallelism
CAUTION:
Keep the parallelism accurate.
Otherwise the circular saw blade may bite into the
guide rail and the damaged guide rail may cause an
injury.
This adjustment has been made at the factory. But if it is
off, you can adjust it as the following procedure.
1.
S et th e tool to th e max imum c utting d epth .
2.
Make sure all lev ers and sc rew s are tigh tened .
3.
Loosen the screws shown in the figure.
4.
While opening the lower guard, move the rear of
th e base so th at th e d istanc e A and B bec omes eq ual.
Fig.50:
1.
S c rew
2.
Base
5.
T igh ten th e sc rew s and make a test c ut to c h ec k
th e parallelism.
OPTIONAL
ACCESSORIES
CAUTION:
These accessories or attachments
are recommended for use with your Makita tool
specified in this manual.
The use of any other
ac c essories or attac h ments migh t present a risk of
injury to persons. Only use accessory or attachment
f or its stated purpose.
If you need any assistance for more details regard
-
ing these accessories, ask your local Makita Service
C enter.
•
C irc ular saw blad e
Rip fence (Guide rule)
•
H ook
•
G uid e rail
•
Bev el guid e
•
C lamp
•
S h eet
•
R ubber sh eet
•
P osition sh eet
Dust nozzle
•
H ex w renc h
Wireless unit (for D S
)
Makita genuine battery and charger
NOTE:
Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.
Содержание DHS782
