Makita DHS782, Инструкция по эксплуатации

Страница: 15 / 164

15 ENGLISH
Indicating the remaining battery capacity
Only for battery cartridges with the indicator
Fig.9 : 1. I nd ic ator lamps 2. C h ec k button
Press the check button on the battery cartridge to indicate the remain
-
ing battery capacity. The indicator lamps light up for a few seconds.
Indicator lamps Remaining
capacity
Lighted Off Blinking
75 % to 1 00%
5 0% to 75 %
25 % to 5 0%
0% to 25 %
C h arge th e
battery.
The battery
may have
malf unc tioned .
NOTE: D epend ing on th e c ond itions of use and th e
ambient temperature, the indication may differ slightly
from the actual capacity.
Switch action
WARNING:
Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the " OFF" position when released.
WARNING:
NEVER defeat the lock-off button
by taping down or some other means. A sw itc h w ith
a negated lock-off button may result in unintentional
operation and serious personal injury.
WARNING:
NEVER use the tool if it runs when
you simply pull the switch trigger without press-
ing the lock-off button.
A sw itc h in need of repair
may result in unintentional operation and serious
personal injury. Return tool to a Makita service center
f or proper repairs BEF O R E f urth er usage.
To prevent the switch trigger from being accidentally pulled, a lock-
of f button is prov id ed . T o start th e tool, d epress th e loc k-of f button
and pull th e sw itc h trigger. R elease th e sw itc h trigger to stop.
Fig.10: 1. S w itc h trigger 2. L oc k-of f button
NOTICE:
Do not pull the switch trigger hard
without pressing in the lock-off button. T h is c an
c ause sw itc h breakage.
CAUTION:
The tool starts to brake the cir-
cular saw blade rotation immediately after you
release the switch trigger. Hold the tool firmly to
respond the reaction of the brake when releasing
the switch trigger.
S ud d en reac tion c an d rop th e tool
off your hand and can cause a personal injury.
Automatic speed change function
T h is tool h as " h igh speed mod e" and " h igh torq ue
mod e" .
The tool automatically changes the operation mode
depending on the work load. When the work load is low,
th e tool w ill run in th e " h igh speed mod e" f or q uic ker
cutting operation. When the work load is high, the tool
w ill run in th e " h igh torq ue mod e" f or pow erf ul c utting
operation.
Fig.11: 1. Mod e ind ic ator
T h e mod e ind ic ator ligh ts up in green w h en th e tool is
running in " h igh torq ue mod e" .
I f th e tool is operated w ith ex c essiv e load , th e mod e
ind ic ator w ill blink in green. T h e mod e ind ic ator stops
blinking and then lights up or turns off if you reduce the
load on th e tool.
Mode indicator status Operation
mode
On Off Blinking
H igh speed
mod e
H igh torq ue
mod e
O v erload
alert
Adjusting depth of cut
CAUTION:
After adjusting the depth of cut,
always tighten the lever securely.
L oosen th e lev er on th e d epth guid e and mov e th e base
up or d ow n. A t th e d esired d epth of c ut, sec ure th e base
by tightening the lever.
F or c leaner, saf er c uts, set c ut d epth so th at no more
than one blade tooth projects below workpiece. Using
proper c ut d epth h elps to red uc e potential f or d anger-
ous KICKBACKS which can cause personal injury.
Fig.12: 1. L ev er
Bevel cutting
CAUTION:
After adjusting the bevel angle,
always tighten the clamping screws securely.
L oosen th e c lamping sc rew s. S et f or th e d esired angle
by tilting accordingly, then tighten the clamping screws
securely.
Fig.13: 1. C lamping sc rew
Use the stopper when you do precise angle cutting.
Fully turn the stopper as illustrated depending on -
4 5 ° bev el c ut or 0° - 4 8 ° bev el c ut.
Fig.14: 1. S topper