Majestic MERID36IN Скачать руководство пользователя

Страница: 75 / 75

Majestic • MERID36IN, MERID36IL, MERID42IN, MERID42IL Installation Manual • 2517-980 Rev. C • 3/18

B. Accessories

Optional Remote Controls, Wall Controls

and Wall Switches

Follow the instructions supplied with the control installed

to operate your fireplace:
For safety:
• Install a switch lock or a wall/remote control with child

protection lockout feature.

• Keep remote controls out of reach of children.
See your dealer if you have questions.

Optional Fan

Follow the instructions supplied with the fan kit to operate

your fan. See your dealer if you have questions.

Optional Fiber or Glass Refractory

An optional refractory kit is available for this model.

Contact your dealer if you have questions.

Please contact your Majestic dealer with any questions or concerns.

For the location of your nearest Majestic dealer,

please visit www.majesticproducts.com.

Majestic, a brand of Hearth & Home Technologies

7571 215

Street West, Lakeville, MN 55044

www.majesticproducts.com

Optional Heat Management Kits

Follow the instructions supplied with the kit for operation.
• Preparation of the appliance for installation of a heat

management kit is discussed in Section 6.B.

Contact your dealer if you have questions.

Содержание MERID36IN












































































Результаты поиска

Содержание MERID36IN

Отзывы:

Похожие инструкции для MERID36IN

Бренды по названию

Популярные бренды

Majestic MERID36IN, Руководство по установке

Результаты поиска

Содержание MERID36IN

Отзывы:

Похожие инструкции для MERID36IN

Бренды по названию

Популярные бренды