Majestic MERID36IN Скачать руководство пользователя

Страница: 40 / 75

Majestic • MERID36IN, MERID36IL, MERID42IN, MERID42IL Installation Manual • 2517-980 Rev. C • 3/18

Assemble Vent Sections
(SLP Only)

To attach the first vent component to the starting collars

of the appliance:

• Attach a DVP-SLP24 adapter to the starting collar of the

appliance.

• Lock the vent components into place by sliding the pipe

section onto the collar.

• Align the seam of the pipe and seam of collar to allow

engagement. Rotate the vent component to lock into

place. Use this procedure for all vent components. See

Figure 7.5.

• Slide the gasket over the first vent section and place it

flush to the appliance. This will prevent cold air infiltration.

Caulk with a minimum of 300 ºF continuous exposure

rating may be used to hold the part in place.

• Continue adding vent components, locking each

succeeding component into place.

• Ensure that each succeeding vent component is securely

fitted and locked into the preceding component.

Required Commercial, Multi-family (Multi-level exceeding

two stories), or High-Rise Applications

All outer pipe joints must be sealed with high temperature

silicone (300 ºF minimum continuous exposure rating), in

cluding the slip section that connects directly to the hori-

zontal termination cap.
• Apply a bead of silicone sealant (300 ºF minimum con

tinuous exposure rating) inside the female outer pipe

joint prior to joining sections. See Figure 7.1.

Apply a bead of silicone sealant (300 ºF minimum con

tinuous exposure rating) to the outside of connecting

joint after joining sections

Apply aluminum foil tape (300 ºF minimum continuous

exposure rating) to the outside of connecting joint after

joining sections. On horizontal pipe runs, it is recom

mended that the tape seam is positioned on the bottom

side of the vent pipe.

• Only outer pipes need to be sealed. All unit collar, pipe,

slip section, elbow and cap outer flues shall be sealed

in this manner, unless

otherwise stated.

Figure 7.5 Adding Venting Components

WARNING! Risk of Fire or Explosion! DO NOT

break

silicone seals on slip sections. Use care when remov-

ing termination cap from slip pipe. If slip section seals

are broken during removal of the termination cap, vent

could leak.

Note: Align seams to engage pipe,

then rotate counterclockwise to lock

B. Assemble Slip Sections

• Slide the inner flue of the slip section into the inner flue

of the pipe section and the outer flue of the slip section

over the outer flue of the pipe section. See Figure 7.6.

• Slide together to the desired length.

Figure 7.6 Slip Section Pilot Holes

Figure 7.7 Screws into Slip Section

Pilot hole

• Continue adding pipe as necessary following instructions

in “Assembling Pipe Sections.”

NOTICE:

If slip section is too long, the inner and outer flues

of the slip section can be cut to the desired length.

• Maintain a 1-1/2 in. (38 mm) overlap between the slip

section and the pipe section.

• Secure the pipe and slip section with two screws no

longer than 1/2 in. (13 mm), using the pilot holes in the

slip section. See Figure 7.7.

Содержание MERID36IN












































































Результаты поиска

Содержание MERID36IN

Отзывы:

Похожие инструкции для MERID36IN

Бренды по названию

Популярные бренды

Majestic MERID36IN, Руководство по установке

Результаты поиска

Содержание MERID36IN

Отзывы:

Похожие инструкции для MERID36IN

Бренды по названию

Популярные бренды