Majestic MERID36IN Скачать руководство пользователя

Страница: 33 / 75

Majestic • MERID36IN, MERID36IL, MERID42IN, MERID42IL Installation Manual • 2517-980 Rev. C • 3/18

B. Wall Penetration Framing/Firestops

Combustible Wall Penetration

Whenever a combustible wall is penetrated, you must

frame a hole for the wall shield firestop(s). The wall shield

firestop maintains minimum clearances and prevents cold

air infiltration.

• The opening must be framed on all four sides using the

same size framing materials as those used in the wall

construction.

• SLP pipe - A wall shield firestop must be placed on each

side of an interior wall. A minimum 1-1/2 in. (38 mm)

overlap of attached heat shields must be maintained.

• DVP pipe - A wall shield firestop is required on one side

only on interior walls. If your local inspector requires a

wall shield firestop on both sides, then both wall shield

firestops must have a heat shield (refer to Section

12.A.) attached to them.

• See Section 7.F. for information for regarding the instal

lation of a horizontal termination cap.

Non-Combustible Wall Penetration

If the hole being penetrated is surrounded by non-com-

bustible materials such as concrete, a hole with diameter

one inch greater than the pipe is acceptable.

Whenever a non-combustible wall is penetrated, the wall

shield firestop is only required on one side and no heat

shield is necessary.

Figure 5.3 Wall Penetration

10 in.

12 in.

10 in.

12 in.

ELBOW HEAT SHIELD

DO NOT PACK HOLE

WITH INSULATION OR

OTHER MATERIAL.

* Shows center of vent framing hole for top or rear venting. The center of the

hole is one (1) in. (25 mm) above the center of the horizontal vent pipe.

MERID36IN/IL

in.

42-3/4

27-7/8

41-3/4

26-7/8

1086

708

1060

683

MERID42IN/IL

in.

45-1/8

29-7/8

44-1/8

28-7/8

1146

759

1121

733

WARNING! Risk of Fire!

Elbow heat shield required

when V

= 2 ft. or less. Clearances to combustibles

must be maintained. See Section 5.A.

Содержание MERID36IN












































































Результаты поиска

Содержание MERID36IN

Отзывы:

Похожие инструкции для MERID36IN

Бренды по названию

Популярные бренды

Majestic MERID36IN, Руководство по установке

Результаты поиска

Содержание MERID36IN

Отзывы:

Похожие инструкции для MERID36IN

Бренды по названию

Популярные бренды