Majestic MERID36IN Скачать руководство пользователя

Страница: 34 / 75

Majestic • MERID36IN, MERID36IL, MERID42IN, MERID42IL Installation Manual • 2517-980 Rev. C • 3/18

C. Ceiling Firestop/Floor Penetra-

tion Framing

A ceiling firestop

MUST

be used between

floors and attics.

•

DVP pipe only

- Frame an opening 10 in.

by 10 in. (254 mm by 254 mm) whenever

the vent penetrates a ceiling/floor (see

Figure 5.4).

•

SLP pipe only

- Frame opening 9 in. x 9

in. (229 mm x 229 mm)

whenever the vent

penetrates a ceiling/floor (see Figure 5.4).

• Frame the area with the same sized lumber

as used in ceiling/floor joist.

• The ceiling firestop may be installed above or

below the ceiling joists when installed with an

attic insulation shield. It must be under joists

between floors that are not insulated. Refer

to Figure 5.5.

• Secure in place with nails or screws.

WARNING! Risk of Fire! DO NOT pack insu-

lation around the vent. Insulation must be kept

back from the pipe to prevent overheating.

Figure 5.4 Installing Ceiling Firestop

Figure 5.5 Installing the Attic Shield

INSTALL ATTIC INSULATION SHIELDS

BEFORE OR AFTER INSTALLATION OF VENT SYSTEM

CEILING FIRESTOP

INSTALLED BELOW CEILING

CEILING FIRESTOP

INSTALLED ABOVE CEILING

ATTIC ABOVE

PIPE
DVP
SLP

10 in. (254 mm)

9 in. (229 mm)

D. Install Attic Insulation Shield

WARNING! Fire Risk. DO NOT

allow loose

materials or insulation to touch vent. Hearth

& Home Technologies requires the use of an

attic shield.

The International Fuel Gas Code requires an

attic shield constructed of 26 gauge minimum

steel that extends at least 2 in. (51 mm) above

insulation.
• Attic insulation shields must meet specified

clearances to combustible materials and be

secured in place.

• An attic insulation shield kit is available from

Hearth & Home Technologies. Contact your

dealer to order. Install attic insulation shield

according to instructions included with kit.

Содержание MERID36IN












































































Результаты поиска

Содержание MERID36IN

Отзывы:

Похожие инструкции для MERID36IN

Бренды по названию

Популярные бренды

Majestic MERID36IN, Руководство по установке

Результаты поиска

Содержание MERID36IN

Отзывы:

Похожие инструкции для MERID36IN

Бренды по названию

Популярные бренды