Majestic MERID36IN Скачать руководство пользователя

Страница: 37 / 75

Majestic • MERID36IN, MERID36IL, MERID42IN, MERID42IL Installation Manual • 2517-980 Rev. C • 3/18

Figure 6.10 (Generic Fireplace Shown)

Attach the first

vent section (it will snap into place). Slide the insulation

gasket (shipped in the manual bag) onto the vent section,

up against the appliance and over the tabs.

Figure 6.11 Heat Management Knockout Locations

HEAT MANAGEMENT KNOCKOUT LOCATIONS

(LEFT AND RIGHT SIDES)

B. Installing Optional Heat Management

Systems

NOTICE:

Additional clearances are required for heat

management systems

installations. Provisions must be

made in advance to ensure fit within the framing.

• Locate the heat management ports on the left and

right sides of the appliance. Either one or two Heat-

Zone

-Gas Kits may be installed.

Remove the knock

out from the fireplace and discard it.

ee Figure 6.11.

• Center the duct collar around the exposed hole and

attach it to the fireplace with 3 screws.

Note:

Do this BEFORE final positioning of fireplace.

• Determine the location for the air register/fan housing

assembly.

Reference the appropriate instructions included with the

kit for the remaining installation steps.

Содержание MERID36IN












































































Результаты поиска

Содержание MERID36IN

Отзывы:

Похожие инструкции для MERID36IN

Бренды по названию

Популярные бренды

Majestic MERID36IN, Руководство по установке

Результаты поиска

Содержание MERID36IN

Отзывы:

Похожие инструкции для MERID36IN

Бренды по названию

Популярные бренды