Majestic MERID36IN Скачать руководство пользователя

Страница: 58 / 75

Majestic • MERID36IN, MERID36IL, MERID42IN, MERID42IL Installation Manual • 2517-980 Rev. C • 3/18

. (LOG A):

Locate the two pin holes on the bottom of

Log A. Hold the log so that the flat spot is facing the rear

of the appliance and the pin holes are facing the base

pan. Place Log A over the two pins referenced for Log A

in Figure 4. Refer to Figure 5.

Figure 5. Log A Installed

. (LOG B):

Locate the pin hole on the bottom of Log B.

Place pin hole on Log B over the pin referenced for Log B in

Figure 4. Hold the log over the pin and rotate the left side

of the log until it contacts the left grate tine. See Figure 6.

Figure 6. Log B Installed

. (LOG C):

Locate the notch on Log C. Place the notch

over the center grate tine as shown in Figure 7. Slide the

log toward the front of the appliance until the portion of

the log closest to the rear of the firebox contacts the right

grate tine.

Figure 7. Log C Installed

NOTCH

. (LOG D):

Log D will utilize two flat spots for its placement

as shown in Figure 7. The flat spots are located on Log

A and on Log C. Locate the end of Log D that does not

have bark and place it into the notch on Log A. Place the

other end of Log D on the flat spot on Log C. See Figure

8. The front edge of Log A may lift slightly off the burner/

hearth pan when Log D is placed properly.

NOTCH FOR LOG D

FLAT SPOT FOR LOG D

FLAT SPOTS

FOR LOG E

Figure 8. Log D Installed

LOG CONTACTS

RIGHT GRATE TINE

LOG CONTACTS

LEFT GRATE TINE

LOG INSTALLATION:

Note:

Logs are placed in appliance in alphabetical order.

Содержание MERID36IN












































































Результаты поиска

Содержание MERID36IN

Отзывы:

Похожие инструкции для MERID36IN

Бренды по названию

Популярные бренды

Majestic MERID36IN, Руководство по установке

Результаты поиска

Содержание MERID36IN

Отзывы:

Похожие инструкции для MERID36IN

Бренды по названию

Популярные бренды