Majestic MERID36IN Скачать руководство пользователя

Страница: 50 / 75

Majestic • MERID36IN, MERID36IL, MERID42IN, MERID42IL Installation Manual • 2517-980 Rev. C • 3/18

Finishing

A. Facing Material

• Metal front faces may be covered with non-combustible

materials only.

• Facing and/or finishing materials must not interfere with

air flow through or removal of decorative fronts or access

for service.

• Facing and/or finishing materials must never overhang

into the glass opening.

• Observe all clearances when applying combustible

materials.

• Seal joints between the finished wall and appliance top

and sides using a 300 ºF minimum sealant. Refer to

Figure 10.1 and Figure 10.2.

WARNING! Risk of Fire! DO NOT

apply combustible

materials beyond the minimum clearances. Comply with

all minimum clearances to combustibles as specified in

this manual. Overlapping materials could ignite and will

interfere with air flow through decorative fronts.

Figure 10.2 Noncombustible Facing Diagram

FACTORY-INSTALLED NON-COMBUSTIBLE BOARD

DO NOT REMOVE

MERID36IN/IL

inches

40-7/8

millimeters

1038

1041

MERID42IN/IL

inches

42-7/8

millimeters

1089

1219

Figure 10.1 Facing Materials

HIGH TEMPERATURE (300 ºF/ 149 ºC MIN.)

TOP AND SIDE SEAL JOINT

BOTTOM 1 INCH (SHADED AREA)

MAY BE COVERED WITH COMBUSTIBLE

OR NON-COMBUSTIBLE MATERIAL

1 IN.

0 IN.

FACING MATERIAL UP TO 1/2 IN. THICK

MAY BE COMBUSTIBLE - TOP AND SIDES

Содержание MERID36IN












































































Результаты поиска

Содержание MERID36IN

Отзывы:

Похожие инструкции для MERID36IN

Бренды по названию

Популярные бренды

Majestic MERID36IN, Руководство по установке

Результаты поиска

Содержание MERID36IN

Отзывы:

Похожие инструкции для MERID36IN

Бренды по названию

Популярные бренды