background image

 1 

 

 

 

 

                        7045-910 

 

 

 

           October 14, 2013

41-I ACC WOOD INSERT

Automatic Combustion Control (ACC)

Model(s):

41I-ACC

 

 

HOT SURFACES!

 

 

Glass and other surfaces are hot 

 

 

during operation AND cool down.  

Hot glass will cause burns.

• 

Do not touch glass until it is cooled

• 

NEVER allow children to touch glass

• 

Keep children away

• 

CAREFULLY SUPERVISE children in same room as 

fireplace.

• 

Alert children and adults to hazards of high temperatures

• 

High temperatures may ignite clothing or other 

flammable materials.

• 

Keep clothing, furniture, draperies and other flammable 

materials away.

 WARNING

If the information in these instruc-

tions is not followed exactly, a 

fire may result causing property 

damage, personal injury, or death.

 

•  Do not store or use gasoline or other flam

-

mable vapors and liquids in the vicinity of 

this or any other appliance.

•  Do not overfire - If heater or chimney con

-

nector glows, you are overfiring. Overfiring 

will void your warranty.

•  Comply with all minimum clearances to 

combustibles as specified.  Failure to 

comply may cause house fire.

WARNING

Fire Risk.

For use with solid wood fuel only.

Other fuels may overfire and generate 

poisonous gases (i.e. carbon monoxide).

Installation and service of this appliance should 

be performed by qualified personnel.  Hearth & 

Home Technologies recommends NFI certified 

professionals, or technicians supervised by an 

NFI certified professional.

WARNING

Installation Manual

Installation & Appliance Set-Up

INSTALLER: Leave this manual with party responsible for use and operation. 

OWNER: Retain this manual for future reference. 

NOTICE: DO NOT DISCARD THIS MANUAL

NOTE

To obtain a French translation of this manual, please contact 

your dealer or visit www.quadrafire.com

Pour obtenir une traduction française de ce manuel, s’il vous 

plaît contacter votre revendeur ou visitez www.quadrafire.com

Summary of Contents for 41I-ACC

























Reviews: