Mahindra 10 Cab Series 4510C Скачать руководство пользователя страница 60

Страница: 60 / 115

CHECKS AND SERVICE

PRE-START CHECKS

To avoid problems it is recommended that a range of checks be carried out daily before starting
the tractor.

For full details of the items and frequency please refer to the tables on page

57,58, and 59

▶

Engine coolant

Remove the radiator cap and ensure that the coolant is up to
the filler neck and that it is clean with the correct anti-freeze
or anti corrosion inhibitor in it.

If the coolant is a rusty color, drain the system completely and
refill with the correct mixture of water and anti-freeze or
corrosion inhibitor.

▶

Engine oil

Pull out the stick, wipe it and dip in the oil sump.

Ensure that oil level is between the upper and lower mark
near the upper mark. If too low add oil, but never excess
100hrs.

important

Do not overfill the crankcase with oil.

▶

Transmission oil

Check the level with the dipstick on top of the transmission in rear of the seat.

If the level is low add oil through the filler hole.

Always ensure that you use the correct oil for topping up or oil changes

Caution

Содержание 10 Cab Series 4510C




















































































































Результаты поиска

Содержание 10 Cab Series 4510C

Отзывы:

Похожие инструкции для 10 Cab Series 4510C

Бренды по названию

Популярные бренды

Mahindra 10 Cab Series 4510C, Руководство оператора

Результаты поиска

Содержание 10 Cab Series 4510C

Отзывы:

Похожие инструкции для 10 Cab Series 4510C

Бренды по названию

Популярные бренды