Mahindra 10 Cab Series 4510C Скачать руководство пользователя страница 86

Страница: 86 / 115

Heating system

General description

The heater is switched on and adjusted by rotating the control knob at the roof console, then switching
on the blower and setting the selector at the preferred speed .

To warn the cab up quickly, the knob should be rotated fully clockwise and the blower set to speed 3.

The screen is demisted or defrosted by air directed through a slot vent . For defrost or fast demist, all
other vents should be closed off.

IMPORTANT:

Ventilation is provided by a single blower unit serving both the heating system and the air conditioning

system.

After reaching the desired temperature adjust the system to suit your needs.
Note:

-For ideal system operation, the engine must run at 1000 rpm

2. Speed heating fan 3.Electric resistances 4.Air filter 5.Recirculation inlets
6.Pivotal air diffuser

Before starting the engine, make sure the system is off ( by turning off the ventilation fan)
so as not to overload the battery.

After the system at full power for a long period of time, never turn it off suddenly but let
it first idle for about 20 seconds.

Warning

Содержание 10 Cab Series 4510C




















































































































Результаты поиска

Содержание 10 Cab Series 4510C

Отзывы:

Похожие инструкции для 10 Cab Series 4510C

Бренды по названию

Популярные бренды

Mahindra 10 Cab Series 4510C, Руководство оператора

Результаты поиска

Содержание 10 Cab Series 4510C

Отзывы:

Похожие инструкции для 10 Cab Series 4510C

Бренды по названию

Популярные бренды