Mahindra 10 Cab Series 4510C Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 115

background image

68

GAP ADJUSTMENT ON THE FRONT AXLE

Lift the front with a hydraulic jack to get the wheels of
the ground.

Then loosen the nut and tighten the bolt fully and turn
the bolt ½ to loosen again in order to roll the center
pivot metal freely and tighten the nut again.

While the wheels arte still off the ground, move the
axle on the center pivot as a final check that the gap is
set correctly on the top of the pivot metal

Front axle

Backward Forward

Nut

Bolt

ADJUSTING THE CLUTCH

Using the clutch over a period of time will increase the
free play.

The correct free play of the pedal is 0.78~1.18 in

To adjust, loosen the locknut on the turnbuckle and
adjust.

Check the adjustment and tighten the locknut if the
free play is correct.

ADJUSTING THE BRAKES

As is the case with the clutch, use of the brakes will
change the pedal free play and the balance between
the right and left pedal.

The correct pedal free play is 1.18~ 1.57 in

▶

Adjustment method.

Loosen the locknuts at each end and turn the rod to adjust the brake.
Turning it anticlockwise increases the free play, clockwise decreases it.
Tighten the locknuts.
Check that the free play is correct and the same on both pedals to ensure even braking

«
...
72
73
74
75
76
...
»

Содержание 10 Cab Series 4510C




















































































































Отзывы:

Нет отзывов

Похожие инструкции для 10 Cab Series 4510C

Бренд: Zetor Страницы: 136

Бренд: KitchenAid Страницы: 16

Бренд: KitchenAid Страницы: 12

Hydrasplitter TPL

Бренд: Agria Страницы: 16

TDD PLUS TD60D PLUS

Бренд: New Holland Страницы: 16

Бренд: Daewoo Страницы: 212

Бренд: Yazoo Страницы: 8

Бренд: Mahindra Страницы: 90

Бренд: GE Страницы: 12

Бренд: Eagle Страницы: 22

Proxima Plus 105

Бренд: Zetor Страницы: 197

PROXIMA PLUS 100 2012

Бренд: Zetor Страницы: 212

Бренд: Viking Страницы: 7

Бренд: Toro Страницы: 12

Бренд: Toro Страницы: 120

Бренд: MID WEST PRODUCTS Страницы: 4

46'' Garden Tractor Plow System

Бренд: Motoalliance Страницы: 13

Бренд: Grammer Страницы: 85

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды