Mahindra 10 Cab Series 4510C Скачать руководство пользователя страница 92

Страница: 92 / 115

3. Checking the air conditioning system.

①

Economic friendly refrigerant : R134a 0.7

∼

0.85Kg.

The presence of air and water in the system could jeopardize its efficiency.

-The air is uselessly compressed by the compressor and no cooling effect is produced.

-The moisture has a tendency rise to obstructions which prevent the cooling efficiency.

②

Check belt tension ; when finger pressure is applied to the mid-point between both pulleys.

③

Condenser fins must always be duly clean using water or an air set.

4. Checking the air conditioning system charge

(1) Check the refrigerant charge.

A.Run the engine at 1500rpm

B. Set the air conditioning system in the coldest for 5 minutes.

C. Check the sight glass dear or cloud

If the air-con. is operated with not charged.

The lubrication in the compressor can cause the damage.

Caution

(2) Check the refrigerant with receive drier sight glass

Abnormal

●

Replenish the refrigerant

●

High pressure pipe is hot and low

pressure pipe is a little cool.

●

H.L pressure of the pressure gauge

needle indicates low pressure.

●

Same bubble appeared

occasionally

(1~2 sec. gap)

Abnormal

●

Deficient of refrigerant

Replenish

●

Nothing different temperature

between H.L pipe

●

High pressure of the pressure

gauge needle indicates low pressure

●

Bubbles flow and

refrigerant gas

disappeared like a fog

flows

Trouble shoot

Bubbles or foam visible

Содержание 10 Cab Series 4510C




















































































































Результаты поиска

Содержание 10 Cab Series 4510C

Отзывы:

Похожие инструкции для 10 Cab Series 4510C

Бренды по названию

Популярные бренды

Mahindra 10 Cab Series 4510C, Руководство оператора

Результаты поиска

Содержание 10 Cab Series 4510C

Отзывы:

Похожие инструкции для 10 Cab Series 4510C

Бренды по названию

Популярные бренды