Mahindra 10 Cab Series 4510C Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 115

background image

50

▶

Fuel gauge.

To avoid excessive condensation in the fuel tank refill at the end of each
day’s work and ensure during the day that it does not drop to a low level
where the fuel system will require bleeding to expel air in the system after
refilling the tank.

▶

Engine cooling water.

If the gauge indicates that the engine is running hot, stop the tractor and
check the coolant in the radiator.

Danger

Also check to ensure that the fins in the radiator core are not clogged or that the tractor has a
broken or stretched fan belt.

When traveling on public or farm roads connect both brake pedals and allow
for the weight of any mounted implement to ensure that the unit is not
unbalanced.

Also allow for the width when passing other road users.

Where fitted use the hazard lights provided.

Strictly follow the local traffic regulations.

Caution

When operating near others with an implement attached take particular care to
allow for the width of the implement and avoid accidents.

Caution

Allow the engine to cool down before opening radiator cap as serious burns
may result due to hot steam & boiling water.

«
...
55
56
57
58
59
...
»

Содержание 10 Cab Series 4510C




















































































































Отзывы:

Нет отзывов

Похожие инструкции для 10 Cab Series 4510C

Бренд: Stockman Страницы: 6

Integrated Compactor 9871915A

Бренд: KitchenAid Страницы: 12

Бренд: KitchenAid Страницы: 6

Бренд: KitchenAid Страницы: 16

Бренд: KitchenAid Страницы: 12

Бренд: KitchenAid Страницы: 12

Бренд: KitchenAid Страницы: 19

Architect Series II W10242569A

Бренд: KitchenAid Страницы: 12

Бренд: KitchenAid Страницы: 4

[12:36:03] ?????????????????: GC900QPPB

Бренд: Whirlpool Страницы: 12

Бренд: Whirlpool Страницы: 18

Бренд: Whirlpool Страницы: 24

Бренд: Textron Страницы: 26

Бренд: MTD Страницы: 2

Бренд: Dong Feng Страницы: 67

Бренд: R2 RINALDI Страницы: 26

Бренд: Bad Boy Страницы: 128

Бренд: Taylor-Dunn Страницы: 180

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды