Mahindra 10 Cab Series 4510C Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 115

background image

FOREWARD

Thank you very much for purchasing our tractor, which, we feel sure, will give you many years of
troubling the service.

The introduction in this manual set out the correct manner of operating, maintaining and checking
the tractor to ensure long-term durability.

Please ensure correct operation of the tractor as incorrect operation can cause substantial
mechanical damage as well as cause accidents with the associated injuries.

Please note that in some cases differences can exist between this manual and your tractor due to the
manufacture’s policy of constant product improvement.

In the event that you strike a problem not covered by this manual please contact your nearest dealer
who will assist you in resolving your problem.

1

WARNING

CALIFORNIA Proposition 65 Warning

The Engine Exhaust from this product contains chemicals known to the
state of California to cause cancer,birth defects or other reproductive harm

WARNING SIGNS IN THIS MANUAL

The following warning signs in this manual draw additional attention to items of importance for the
safe and correct operation of the tractor.

Hazard or unsafe practice that can lead in injury or death.

Instructions for the correct operation of the machine which, if
followed, will ensure that it performs at it’s best

Hazard or unsafe practice that can lead to severe injury or death.

Serious hazard with a very high level of risk of either serious
injury or death

MEANING OF THE SIGN

SIGN

All information,illustrations and specifications in this manual are based on latest information
available at the time of publication.The right is reserved to make changes at any time without notice.

Caution

Danger

Warning

Important

«
...
7
8
9
10
11
...
»

Содержание 10 Cab Series 4510C




















































































































Отзывы:

Нет отзывов

Похожие инструкции для 10 Cab Series 4510C

Бренд: Branson Страницы: 132

Бренд: Kubota Страницы: 25

Бренд: Kubota Страницы: 90

Бренд: Broan Страницы: 8

Northstar 11000UNIV

Бренд: Rankin Страницы: 32

GE PROFILETM GCG1500L

Бренд: GE Страницы: 2

Бренд: wsm Страницы: 346

Бренд: Victory Страницы: 91

Бренд: Snapper Страницы: 4

Бренд: Kioti Страницы: 121

Бренд: Kioti Страницы: 135

Бренд: Kioti Страницы: 180

Бренд: Kioti Страницы: 190

Бренд: Iran Tractor Страницы: 106

Бренд: Iran Tractor Страницы: 118

Бренд: Iran Tractor Страницы: 122

Бренд: GOLDONI Страницы: 42

Бренд: GOLDONI Страницы: 153

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды