Mahindra 10 Cab Series 4510C Скачать руководство пользователя страница 79

Страница: 79 / 115

3.MAINTENANCE

For daily or short term storage

Clean the tractor and remove all dirt from field work.

Fill the fuel tank to avoid condensation and rust.

Lower the implement to the ground..

Keep it in a machinery shed or, if not available cover the unit if left outside.

In very cold conditions it is advisable to remove the battery and keep it inside in a warm
environment.

This will ensure effective starting when the tractor is required.

When the outside temperature is below 32

℉

, replace the Antifreeze completely or drain the

coolant to protect the engine from damage from frozen coolant.

important

When washing the tractor ensure that the water does not get near electrical
components or the oil filter points.

To prevent short circuits remove the ignition key.

Do not wash the tractor when the engine is running.

Содержание 10 Cab Series 4510C




















































































































Результаты поиска

Содержание 10 Cab Series 4510C

Отзывы:

Похожие инструкции для 10 Cab Series 4510C

Бренды по названию

Популярные бренды

Mahindra 10 Cab Series 4510C, Руководство оператора

Результаты поиска

Содержание 10 Cab Series 4510C

Отзывы:

Похожие инструкции для 10 Cab Series 4510C

Бренды по названию

Популярные бренды