Mahindra 10 Cab Series 4510C Скачать руководство пользователя страница 36

Страница: 36 / 115

BLINDNESS CAN RESULT

FROM BATTERY EXPLOSION.

KEEP SPARKS OR OPEN

FRAMES AWAY FROM

BATTERY.

DO NOT JUMP START.

BURNS CAN RESULT

FROM BATTERY ACID.

IN CASE OF CONTACT

FLUSH IMMEDIATELY

WITH WATER .

DANGER

Location: On battery bracket RH
part No.: 1260-904-066-0

●

Pull only from drawbar. Pulling from any

other point can cause rear overturn.

●

Do not operate with unshielded PTO.

●

Disengage PTO and stop engine before

servicing tractor or attaching and detaching

implements.

●

When towing equipment use a Safety chain

FAILURE TO FOLLOW ANY OF THE

INSTRUCTIONS ABOVE CAN CAUSE
SERIOUS INJURY TO THE OPERATOR
OR OTHER PERSONS.

WARNING

Location: On rear frame
Part No.: 1260-904-065-0A

FRONT TYRE (9.5-16) PRESSURE

Air pressure: 30 p.s.i

REAR TYRE (13.6-26) PRESSURE
Air pressure: 21.3 p.s.i

●

Start engine only from operators seat.

If safety start switch is bypassed engine can

start with transmission in gear.

●

Do not connect or short across terminal on

starter solenoid.

●

Attach booster cables as shown on battery

decal and operators manual.

Starting in gear causing runaway can result
in serious injury.

WARNING

Location: On dash cover side LH
Part no: 1260- 904-062-0A

Location: On Front Rims.

Location: : On rear rims.

DO NOT REST FOOT ON

CLUTCH PEDAL.

MAY RESULT IN DAMAGE

TO CLUTCH ASSEMBLY.

WARNING

Location: On dash panel near clutch pedal

Part No.: 1260-904-068-0

Содержание 10 Cab Series 4510C




















































































































Результаты поиска

Содержание 10 Cab Series 4510C

Отзывы:

Похожие инструкции для 10 Cab Series 4510C

Бренды по названию

Популярные бренды

Mahindra 10 Cab Series 4510C, Руководство оператора

Результаты поиска

Содержание 10 Cab Series 4510C

Отзывы:

Похожие инструкции для 10 Cab Series 4510C

Бренды по названию

Популярные бренды