Mahindra 10 Cab Series 4510C Скачать руководство пользователя страница 75

Страница: 75 / 115

Uneven adjustment of the left and right pedal will result in one sided braking
when the pedals are connected and can cause serious accidents, especially at
high speeds.

Double check to ensure free play is the same on both pedals

Caution

ADJUSTING THE THROTTLE LEVER

If this lever is either loose or difficult to move please consult your dealer for rectification of the
problem.

ADJUSTING TOE-IN

If the toe-in adjustment is incorrect it can cause severe shaking of both the steering wheel and the entire
tractor.

The correct toe in is 0.08~0.24in. We recommend that this adjustment is made by the dealer.

CHECKING THE BATTERY

The electrolyte level of the battery can evaporate during use
thus lowering the level.

Where it does so replace it with distilled water.

Where a spillage has reduced the level, replace it with
electrolyte.

Electrolyte contains acid and can cause serious burns.

Any spillage on skin should be washed off by running water immediately.

Caution

important

Low electrolyte levels can cause premature battery failure and corrosion.

Содержание 10 Cab Series 4510C




















































































































Результаты поиска

Содержание 10 Cab Series 4510C

Отзывы:

Похожие инструкции для 10 Cab Series 4510C

Бренды по названию

Популярные бренды

Mahindra 10 Cab Series 4510C, Руководство оператора

Результаты поиска

Содержание 10 Cab Series 4510C

Отзывы:

Похожие инструкции для 10 Cab Series 4510C

Бренды по названию

Популярные бренды