manualshive.com logo in svg
background image

 1 of 29

 

 

   

INST

ALLA

TIO

N & OWNER

S MANU

AL

 

Kubota B01

 

Premium Cab p/n: 1KB01PR

 

Standard Cab p/n: 1KB01ST

 

Fits Tractor Models: B2301 and B2601

 

(*=Not including accessories)

 

Premium Cab Shown with Optional Front and Rear LED Work Lights

 

 

Available Options:

 

1. Front LED Work Lights (P/N: 9LEDW4)

 

2. Rear LED Work Lights (P/N: 9LEDW3)

 

3. Strobe Light (P/N: 9LEDS2)

 

4. Dome light (P/N 9LEDD14)

 

5. Heater (P/N: 9PH20S62)

 

6. Switch Panel (P/N: 9PSF1)

 

7. Side View Mirrors (P/N: 9PM5)

 

9. Rear View Mirror (P/N: 9PM3)

 

8. Rear Wiper (P/N: 9PWK85F) 

 

 

Note: Front wiper (P/N: 9PWK110) is supplied with premium cab kit only.

 

Approximate Installation Time *

 

Experienced Dealer Technician –

 3.5 

Hours

 

Average Dealer Technician –

 4.5 

Hours

 

Do

-

It

-

Yourself –

 5.5 

Hours

 

Approximate Product Specifications

 

Floorboard to Roof Height: 62 inches

 

Weight: 290 lbs. (

Premium

), 221 lbs. (

Standard

)

 

Cab Width: 41 inches

 

Rev. D, 07/12/2019

 

p/n: IM

-

1KB01PR

 

The contents of this envelope are the property of the owner. 

 

Leave with the owner when installation is complete.

 

While this cab kit was designed to fit on the vehicle(s) listed above, manufacturing tolerances and vehicle 
assembly may affect cab fitment. It is the responsibility of the cab installer to check all vehicle pedals and 
levers for full functionality and, as required, adjust the cab fitment to prevent any interference of the cab 
components with the travel of pedals or levers.

 

Содержание 1KB01PR






























Отзывы: