Kubota 1KB01PR Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 29

Kubota 1KB01PR Скачать руководство пользователя страница 13

CAB INSTALLATION

13 of 29

Fig. 13.1 (roof installation)

Fig. 13.3 (roof gas shock installation)

STEP 12: (REAR PANEL HEADER)

For Standard Cab only.

If installing a premium cab, proceed to step 13 below.

12.1

Remove the (4) factory install 5/16

-

18 flange hex

nuts from the bottom of the roof. Install the Rear Panel

Header Assembly to the bottom side of the roof. Re

-

install the hex nuts. See fig. 12.1.

Fig. 12.1 (underside of roof with header)

STEP 13: (ROOF)

13.1

With assistance, lift the roof onto the side frames.

See fig. 13.1. Take care not to engage the quick

release latches with the side frame latch pins.

Move the roof into position so that the quick release

latches are engaged into the latch pins found on the

side frames.

13.2

Once the roof is in place, install the left hinge pin

and then the right hinge pin. See fig. 13.2. Ensure that

the roof is square to the side frames and tighten hinge

fasteners.

Hardware Used

Qty

1/4

-

20 X 3/4 FHCS

4

1/4

-

20 Flange Nut

4

13.3

Disengage the roof latches, manually lift the roof,

and install the gas shocks. See fig. 13.3

.

Note: Orient

the gas shocks so that the piston rod is pointing down

for best, continuous seal lubrication and longest gas

shock life.

piston rod

down here

Fig. 13.2 (roof hinge

-

left)

hinge pin

«
...
11
12
13
14
15
...
»

Содержание 1KB01PR






























Отзывы:

Нет отзывов