![background image](http://html.mh-extra.com/html/macdon/m155-2022/m155-2022_operators-manual_685745100.webp)
215676
80
Revision A
Display (Lower or Upper Line)
Description
#### DISC RPM
##.## DISC SENSOR
Displays the rotational speed of the disc
This message appears if the disc speed sensor is disabled. The messages
RPM and SENSOR appear alternately at one-second intervals
##.# HEADER HEIGHT
##.# HEIGHT SENSOR
Displays the distance setting (00.0
–
10.0) between the cutterbar and the
ground
This message appears if the header height sensor is disabled. The messages
HEIGHT and SENSOR appear alternately at one-second intervals
##.# HEADER ANGLE
##.# HEADER SENSOR
Displays the angle setting (00.0
–
10.0) of the header relative to the ground
This message appears if the header angle sensor is disabled. The messages
ANGLE and SENSOR appear alternately at one-second intervals
##.# L FLOAT R ##.#
FLOAT SENS DISABLED
Displays the left and right float settings (0.0
–
10.0)
This message appears if the float sensor is disabled
LOAD|
■■■■
| | ####
This bar graph represents the hydraulic operating pressure of the circuit in
which the hydraulic pressure sensor is installed. The bars will appear to be
full if the preprogrammed overload pressure (17,237
–
34,474 kPa
[2500
–
5000 psi]) is reached. If the hydraulic pressure sensor is disabled, this
message will not appear
13
### °C or F HYD OIL TEMP
### °C or F HYD TEMP
Displays the left and right float settings (0.0
–
10.0)
This message appears if the temperature sensor is disabled. The messages
TEMP and SENSOR appear alternately at one-second intervals
##.# VOLTS
Displays the engine electrical system
’
s operating voltage
##.# SWATH COMPR HT
SWATH CO SENSOR
Displays the swath compressor
’
s height setting(00.0
–
10.0); fully raised is 0
This message appears if the swath compressor height sensor is disabled
SCROLL
SUB-MENU (lower line only)
#### DISC RPM
##.# HEADER HEIGHT
LOAD|
■■■■
|
■■■■
| ####
Displays the sub-menu after two to three seconds. Press SELECT to exit the
sub-menu. Use the CDM switch to scroll through the sub-menu options
Miscellaneous Operational Information
These messages can appear on the cab display module
’
s (CDM) display screen when the windrower is in various
operational states.
Display (Upper Line)
Description
HEADER DISENGAGED
Indicates that the header drive is disengaged
##.# FOOT DISK
Indicates the size of the header attached to the windrower. AUGER or
DRAPER will appear in place of DISK, depending on type of header attached
IN PARK
Indicates that the GSL is in the N-DETENT position
< LEFT TURN
■
Indicates that the left turn indicator system is active. This message appears
when the left turn arrow on the CDM is pressed when the windrower is in
engine-forward mode.
14
)
13. A sensor which can monitor the knife/conditioner circuit pressure can be installed as an optional kit. To monitor the
hydraulic pressure of the reel/auger circuit, relocate the sensor per kit instruction MD #169031; this instruction is
available from your MacDon Dealer.
14. If the windrower
’
s road light kit is not installed, the CDM will display the error message E135 LEFT STOP LAMP when
the windrower is in cab-forward mode.
Содержание M155 2022
