LSC CLARITY LX300 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 226

background image

Clarity

Desktop Clarity

Operator Manual

Page 9

however it is ideal for training and demonstrations or to create off line shows that can be run
on a purchased version of Clarity or on a LX console.

3.6

DESKTOP DMX OUTPUT

DMX512 output is obtained by connecting any of the following devices to the USB port of your
computer. Multiple devices can be connected.



LSC Clarity QX1 interface provides 1 universe of DMX output.



LSC Clarity QX2 interface provides up to 2 universes of DMX output.



LSC Clarity VX10 wing provides up to 2 universes of DMX output.



LSC Clarity VX20 wing provides up to 4 universes of DMX output.

QX1

Provides 1 universe of DMX output

QX2

Provides 2 universes of DMX output

The QX1 and QX2 interfaces are powered directly from the computer’s USB connector. Connect

your DMX controlled equipment to the relevant DMX universe connectors. The DMX outputs are
fully isolated from the USB input.

Note that the DMX output has to be patched in Clarity before it will work. See section 11.12 for
details.

3.7

DESKTOP ARTNET OUTPUT

ArtNet is a protocol that is transmitted over Ethernet LAN (Local Area Network) or WAN (Wide

Area Network) and supports up to 255 DMX Universes on a single cable. To use ArtNet it must
be connected to the internal universes within Clarity in the Patch window. See section 11.13 for
details.

3.8

VX10 PLAYBACK WING

Control of Playback on a computer can be augmented by adding an

LSC Clarity VX10 playback wing. This provides 10 fader Playbacks
with LCD displays and multiple page selection, a Grand Master and

DBO (Dead Black Out), two DMX512 universe outputs, remote
trigger inputs and a secure compartment for installing your license

dongle and a front panel USB port.

Connect the VX10 wing to a USB port of your computer using the cable provided. The VX10 is

powered directly from the computer’s USB connector. A separate power supply is required
when your computer’s USB connector cannot supply sufficient power for the VX10.

VX10 Rear Panel

The rear panel is described in detail below.

Power Input

LED Desk

Lamp Socket

2 DMX Universe Outputs

USB dongle

compartment

Remote Trigger

Inputs

USB to

Computer

Kensington

Lock slot

«
...
15
16
17
18
19
...
»

Содержание CLARITY LX300



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CLARITY LX300

Бренд: Makita Страницы: 7

Бренд: Makita Страницы: 9

Бренд: Makita Страницы: 7

Бренд: Zelmer Страницы: 42

Бренд: Lite-Puter Страницы: 33

Betonmischer 120 Liter Pattfield

Бренд: Pattfield Ergo Tools Страницы: 52

Бренд: QSC Страницы: 26

Бренд: HAGER WERKEN Страницы: 6

Бренд: Grunkel Страницы: 14

MultiMix 16 Firewire

Бренд: Alesis Страницы: 51

Бренд: Ozito Страницы: 10

Бренд: GE Страницы: 20

Бренд: GE Страницы: 28

Бренд: GE Страницы: 24

Бренд: GE Страницы: 12

Xcellerex XDM 100

Бренд: GE Страницы: 322

Бренд: GE Страницы: 4

Бренд: Samson Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды