Lissmac UNICUT 520 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 92

background image

29/92

5.1.

Joystick

Joystick position when starting the machine!

If the joystick is not in the neutral position when starting, it must first be set to neutral position to be able to
move the machine.

Joystick movement

All steering and thumbwheel control commands should be carried out in a smooth and controlled fashion!

Assignment
Deep cutting only

Steering mode 1 / 2*

toggle

Water pump on / off

Multifunction button

Lift blade guard

Lift saw blade

Lower blade guard

Lower the saw blade

Saw blade motor on / off

Toe in on / off

Rapid traverse

(press and hold down)

Fine steering

(for precise steering
corrections
in cutting operation)

*Steering modes 1 / 2

Steering mode 1 controlled:

If the joystick is tilted to the right or to the left, the wheels will follow the deflection angle of the joystick and
remain in this position. There is no reset!
To go straight ahead, the joystick must again be actively guided to the middle position (counter-steer).

Steering mode 2 regulated:

If the joystick is tilted to the right or left, the wheels will follow the deflection angle of the joystick.
When the joystick is released, it goes to the middle position by itself and the wheels automatically reset to
0° (straight ahead).

Forward

(invert with pre-selection page 1 (item 4))

Right

Left

Backward

(invert with pre-selection page 1 (item 4))

Neutral position

«
...
27
28
29
30
31
...
»

Содержание UNICUT 520





























































































Отзывы:

Нет отзывов

Похожие инструкции для UNICUT 520

Бренд: Target Страницы: 40

Бренд: Weka Страницы: 31

Бренд: Clarke Страницы: 16

Бренд: Powermatic Страницы: 48

Бренд: RADLEY Страницы: 22

Бренд: Bosch Страницы: 108

Бренд: Bosch Страницы: 183

Бренд: Bosch Страницы: 57

Бренд: AMERI-CAN MACHINERY Страницы: 19

Delta S36-300T2

Бренд: ShopMaster Страницы: 80

Бренд: Dexter Power Страницы: 48

Бренд: Status Страницы: 18

Бренд: PowerTec Страницы: 20

Бренд: Hitachi Koki Страницы: 90

Бренд: Hitachi Koki Страницы: 32

Бренд: Meec tools Страницы: 49

Бренд: Xtreme Power Страницы: 10

Бренд: NATI Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды