Lissmac UNICUT 520 Скачать руководство пользователя страница 49

Страница: 49 / 92

49/92

7.6.

Setting toe in

The saw blade for deep cuts tends to pull the machine to one side.
This is completely normal and can easily be corrected via the toe-in adjustment to ensure a straight cut.

The dashboard page can be accessed at any time using the "Dashboard" button (item 2).

Sequence



Press rotary switch (item 1) to activate the middle menu.



Select first element (item 16) and confirm by pressing the rotary switch (item 1).



By turning the rotary switch (item 1), the toe-in value can be set in degrees.



Confirm the set value by pressing the rotary switch (item 1).

The toe-in adjustment can be activated or deactivated at any time using the joystick button 5.

Every steering correction on the joystick deactivates the automatic toe-in. To reactivate, press button 5 again.

-0.6°

Содержание UNICUT 520





























































































Результаты поиска

Содержание UNICUT 520

Отзывы:

Похожие инструкции для UNICUT 520

Бренды по названию

Популярные бренды

Lissmac UNICUT 520, Руководство по эксплуатации

Результаты поиска

Содержание UNICUT 520

Отзывы:

Похожие инструкции для UNICUT 520

Бренды по названию

Популярные бренды