manualshive.com logo in svg

Lighthouse Worldwide Solutions ApexR02, Руководство по эксплуатации

Ищите операционное руководство для Lighthouse Worldwide Solutions ApexR02? Инструкция доступна для скачивания бесплатно на manualshive.com. Получите все необходимые сведения о продукте, просто скачав руководство по эксплуатации. Узнайте, как максимально использовать функционал этого устройства.

Поделиться
Скачать
background image

Lighthouse ApexRemote Operating Manual

t-ii

248083447-1 Rev 1

Communicating with ApexRemote Serial Instrument ...................................................  4-3

Serial Data / Power Port .....................................................................................  4-3

RS-485 Communications .......................................................................  4-5

Communicating with ApexRemote PoE Instrument  .....................................................  4-6

ApexRemote PoE Communications  ..................................................................  4-6

Ethernet Settings: ...................................................................................  4-7

ApexRemote Web Page Interface ..................................................................................  4-8

Chapter 5   Maintenance Procedures

Introduction ....................................................................................................................  5-1
Safety .............................................................................................................................  5-1
Maintenance ...................................................................................................................  5-1

Calibration .........................................................................................................  5-1

Zero Count Test  .............................................................................................................  5-1
Fault Isolation  ................................................................................................................  5-2
Instrument Service Report  .............................................................................................  5-2

Chapter 6   Program with the MODBUS Protocol

DIP Switches ..................................................................................................................  6-1
Protocol Settings  ............................................................................................................  6-1
Power On/Auto Start ......................................................................................................  6-1
Running the Instrument Using MODBUS .....................................................................  6-2

AUTOMATIC Counting Mode  .........................................................................  6-2

Configuring with the MODBUS Protocol  .....................................................................  6-3

Setting the Real Time Clock ..............................................................................  6-3
Changing the Default Instrument Parameters  ....................................................  6-4

Using Sensor Setting Registers ..............................................................  6-4
Location (Register 40026)  .....................................................................  6-5
Hold Time (Registers 40031, 40032)  ....................................................  6-5
Sample Time (Registers 40033, 40034)  ................................................  6-5

Alarm Enable Registers  .....................................................................................  6-6

Enable Alarming for a Channel  .............................................................  6-7

Threshold Setup Registers  .................................................................................  6-7

Setting the Alarm Threshold Value  .......................................................  6-8

Chapter 7   Install

Install the ApexRemote  .................................................................................................  7-1

Installation Basics: .............................................................................................  7-1
Installing the SmartBracket/ApexRemote  .........................................................  7-1

Tools/Hardware Required: .....................................................................  7-1

Installing ApexRemote without SmartBracket  ..................................................  7-4

Communication Ports  ....................................................................................................  7-6

Содержание ApexR02





















































































Отзывы:

Нет отзывов

Похожие инструкции для ApexR02

Bacharach MGS-401 User Manual preview
MGS-401
Бренд: Bacharach Страницы: 19
Keithley TEC SourceMeter 2510 User Manual preview
TEC SourceMeter 2510
Бренд: Keithley Страницы: 244
Kawai KX1000 Owner'S Manual preview
KX1000
Бренд: Kawai Страницы: 112
Hach 2100A User Manual preview
2100A
Бренд: Hach Страницы: 96
Emos P5821 Manual preview
P5821
Бренд: Emos Страницы: 76
Hanna Instruments HI 93414 Instruction Manual preview
HI 93414
Бренд: Hanna Instruments Страницы: 52
Badger Meter Recordall Series User Manual preview
Recordall Series
Бренд: Badger Meter Страницы: 8
Bontempi 047663337760 Owner'S Manual preview
047663337760
Бренд: Bontempi Страницы: 18
Bruker BioSpin minispec mq10 User Manual preview
minispec mq10
Бренд: Bruker BioSpin Страницы: 76
OmegaWatt Multivoies Pad User Manual preview
Multivoies Pad
Бренд: OmegaWatt Страницы: 9
ACCEL DFI Engine Analyzer Series Installation And Instruction Manual preview
Engine Analyzer Series
Бренд: ACCEL DFI Страницы: 39
Lutron Electronics VB-8213 Operation Manual preview
VB-8213
Бренд: Lutron Electronics Страницы: 23
Kirby Morgan KMB-18 A/B Operation And Maintenance Manual preview
KMB-18 A/B
Бренд: Kirby Morgan Страницы: 101
BASI BFM921 User Manual preview
BFM921
Бренд: BASI Страницы: 69
LORECa Hearing Instrument PKA87 User Manual preview
PKA87
Бренд: LORECa Hearing Instrument Страницы: 43
Vanguard Instruments Company TRF-100 User Manual preview
TRF-100
Бренд: Vanguard Instruments Company Страницы: 111
Polimaster PM1703GNA-II Operation Manual preview
PM1703GNA-II
Бренд: Polimaster Страницы: 24
Hanna Instruments HI 93727 Instruction Manual preview
HI 93727
Бренд: Hanna Instruments Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды