background image

ApexRemote MODBUS Register Map v1.50

248083447-1 Rev 1

A-9

response.  When this register is read, it always returns a zero.

Table A-7  Command Register

Value

Action

1

Saves all writable 4xxxx register values to the EEPROM.

2

Reserved for future use.

3

Clears the Data Buffer.  Record count is set to zero.

4

Saves the instrument parameters in the 40xxx registers to the 
EEPROM. Parameters include Sample Time, Hold Time, Initial 
Delay, and Location.

11

Instrument Start (Automatic Counting).
Particle Counters:  Uses defined Initial Delay, Hold Time, Sample 
Interval and counting mode.  Instrument executes samples and holds 
until an Instrument Stop command is issued.  For instruments with 
pumps, this command will start the pump.
Manifold Controller:  Uses defined Manifold Sequence.  Stops 
counting and changing position when Instrument Stop command is 
issued.

12

Instrument Stop.  Aborts current sample.  Stops pump, if applicable.  
Stops data collection.

13

Set Real Time Clock.
Writes "Data Set" values (from Registers 40035 & 40036) to the 
local Real Time Clock. New time value is saved.

17

Instrument Location Validation Start:
ApexRemote:
Start blinking Alarm LED blue.

18

Instrument Location Validation Stop
ApexRemote:
Stop blinking Alarm LED blue.

19

Instrument Data Validation Start
ApexRemote:
Start sampling with dummy data using current sampling parameters. 
Data is also tagged as validation.

20

Instrument Data Validation Stop
ApexRemote:
Stop sampling with dummy data using current sampling parameters. 
Data is also tagged as validation.

Содержание ApexR02





















































































Отзывы: