Lighthouse Worldwide Solutions ApexR02 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 84

background image

Get Started

248083447-1 Rev 1

3-9

Operation

Understanding the LEDs

The

Apex

Remote

LEDs have specific meanings when illuminated.

Figure 3-10 below shows the location of the LEDs and gives a brief
description of their meaning.

Figure 3-10 Front Panel LEDs

•

The green POWER LED turns on steady when the instrument is
powered on and OFF when power is removed.

•

The green FLOW LED turns on steady when the flow is within
specification and will blink if the flow is out of specification.

•

The amber SERVICE LED will be OFF under normal operating
conditions and will turn on steady during sampling if LASER
power or current is out of range, LASER supply or photoamp
supply is out of range or the photoamp health is bad. The Service
LED will blink at 1Hz when the sensor background voltage is out
of range, indicating the sensor optics are dirty or the view volume
contains foreign objects.

•

The blue SAMPLING LED is ON when sampling and OFF when
the

Apex

Remote

is idle.

•

The Alarm LED is OFF when no alarms are enabled, green when
alarms are set but not exceeded, and red when a set threshold has
been exceeded. A 5Hz blue flashing means

Apex

Remote

is in

validation mode and 5Hz white flashing when the unit is in

SmartBracket

mode but a

SmartBracket

can’t be detected.

Green

=on steady

Green

ON = good flow; ON/OFF = Fail

Amber

Blue

= Sampling; OFF = Idle; BLINK =

Green

= Alarm enabled, no alarm

with power on

OFF = Pass; ON = Sensor in

Red

= Threshold exceeded

Blue flash

= Validate mode ON

White flash = SmartBracket installed

but not connected to ApexRemote

OFF= no alarms enabled & not in

validate mode

@1Hz, @5Hz = no flow

need of service

sensor may be contaminated

Power LED

Flow LED

Service LED

Sampling LED

Alarm LED

«
...
29
30
31
32
33
...
»

Содержание ApexR02





















































































Отзывы:

Нет отзывов

Похожие инструкции для ApexR02

Бренд: janitza Страницы: 12

Бренд: janitza Страницы: 84

Бренд: janitza Страницы: 6

Бренд: janitza Страницы: 14

Бренд: janitza Страницы: 98

Бренд: Fluke Calibration Страницы: 13

Бренд: Kipp & Zonen Страницы: 32

Бренд: Alfa Laval Страницы: 18

Бренд: Eno Scientific Страницы: 47

EA Heightmaster +

Бренд: PROLEC Страницы: 38

Бренд: Magnescale Страницы: 36

Бренд: Rubicson Страницы: 4

Бренд: L.R. Baggs Страницы: 6

Бренд: Princeton Instruments Страницы: 28

Бренд: BANTE Страницы: 17

Бренд: E+E Elektronik Страницы: 4

Бренд: yellow jacket Страницы: 16

WTW pH/ION 3310

Бренд: Xylem Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды