Lighthouse Worldwide Solutions ApexR02 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 84

background image

00

248083447-1 Rev 1

7-1

7

Install

Install the

Apex

Remote

Installation Basics:

This section is provided as an example of a typical

Apex

Remote

installation. The tools and hardware shown are examples and may not
apply to all installations. It is suggested that safety glasses and other
equipment be used to prevent injury. Do

NOT

attempt to drill into a

wall that may have live AC power behind the wallboard being drilled.
Contact Facilities Management personnel to have the area made safe
before beginning installation.

WARNING:

Make

sure the installation
point for the

Apex

Remote

does not

prevent easy disconnect
of the instrument power.

The

Apex

Remote

must be mounted on a vertical flat surface and

must have the Inlet to Outlet path be as close to vertical as possible.

Apex

Remote

Power Supply specifictions are 100-120VAC,

47-63Hz, 0.5A input, 24VDC 750mA output (18W max).

Replacing with a power supply that does not meet these

specifications may void the

Apex

Remote

warranty and risk

exposing equipment and users to fire and shock hazard.

If replacement of the power supply or its AC power cord is
required, replace only with a power supply or cord having
as good as or better ratings than the items provided by
Lighthouse Worldwide Solutions. Attempting to use an
under-rated power supply or cord can expose the
instrument power supply, adjacent equipment or the user to
dangerous shock and fire hazards. Failure to heed this
warning can result in personal injury or death.

Installing the

SmartBracket/

Apex

Remote

Tools/Hardware Required:

Every installation of measuring instruments is dependent upon facility
surroundings, construction materials and points of placement. Due to
these differences, specific instructions cannot be supplied in this
document. However, the listed tools and hardware shown in Figure 7-1

«
...
49
50
51
52
53
...
»

Содержание ApexR02





















































































Отзывы:

Нет отзывов

Похожие инструкции для ApexR02

Бренд: E-line Страницы: 164

Бренд: IET Labs Страницы: 114

Бренд: jablotron Страницы: 2

Бренд: Velleman Страницы: 96

Бренд: Yamaha Страницы: 120

Бренд: Yamaha Страницы: 110

Portatone PSR-5700

Бренд: Yamaha Страницы: 79

Бренд: Yamaha Страницы: 112

Бренд: Yamaha Страницы: 82

Бренд: Yamaha Страницы: 108

Бренд: lanry Страницы: 2

Бренд: lanry Страницы: 29

Бренд: Garmin Страницы: 22

Бренд: Vectronics Страницы: 2

Бренд: Resol Страницы: 24

Бренд: FuzzDog Страницы: 6

Бренд: Oberheim Страницы: 41

Бренд: Newton Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды