Lighthouse Worldwide Solutions ApexR02 Скачать руководство пользователя страница 28

Страница: 28 / 84

Lighthouse ApexRemote Operating Manual

3-6

248083447-1 Rev 1

Date Settings:

Figure 3-7 Instrument Date and Time Settings

Note:

Make sure to

update the instrument
settings before the

SmartPort cable

disconnected from the

Apex

Remote

All

Apex

Remote

products can have their date and time settings

changed in this screen. Refer to Figure 3-7 to change the Instrument
Date / Time by using the

Set to System Time.

Corrections to errors

can be reversed by clicking

Restore Values

. Make sure that desired

changes are followed by clicking the

Update Instrument

button to

save the changes to the instrument memory. If the instrument is not
updated before the

SmartPort

cable is disconnected, the changes will

be lost.

Factory
Standard
Settings

Apex

Remote

PoE Model:

The

Apex

Remote

PoE

standard network settings are set to the same

values for all

Apex

Remote

s shipped. These values are 10.10.x.xxx

for IP, 255.255.0.0 for netmask and 0.0.0.0 as Default Gateway setting.
To view the

Apex

Remote

web page, type its IP address into a web

browser on a computer in the same network subnet.

The IT group should provide IP, Mask and Default Gateway values that
meet the local network needs. The

Apex

Remote

must be changed to

meet these requirements. Each device will require the IP to be changed
to a new IP, as shown in Figure 3-8, to prevent address conflicts.

This button loads

and time values

computer date

the

This button saves

the changes to the

memory

into program

memory

instrument

Содержание ApexR02





















































































Результаты поиска

Содержание ApexR02

Отзывы:

Похожие инструкции для ApexR02

Бренды по названию

Популярные бренды

Lighthouse Worldwide Solutions ApexR02, Руководство по эксплуатации

Результаты поиска

Содержание ApexR02

Отзывы:

Похожие инструкции для ApexR02

Бренды по названию

Популярные бренды